Consider the shaded area in (Figure 1). Suppose that a = 9m, k = -1 m 9 4 Figure y = kx² P IM 1 of 1 Part A Locate the centroid of the area. Express your answer to three significant figures and include the appropriate units. 6 a C ? 2= Value Submit Provide Feedback ▼ G Request Answer Units 50%

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: Figure 6(a) shows an example of pressure vessel with radius ofr, and yield stress O. Suppose the…

A: Calculated the minimum thickness to sustain the pressure vessel according to the von mises yield…

Q: What is the CGS unit of surface tension?

A: Given: Surface tension: It is the surface force in the liquid to shrink into the minimum possible…

Q: How The product pressure × volume has energy units.

A: Step 1: Write the units SI units of pressure and volume.

Q: How did you find the Cp values of each?

A: Cp - Cp is known as  Specific heat at constant pressure.

Q: ɴᴀᴍᴇ ᴛʜᴇ ᴘᴀʀᴛꜱ ᴏꜰ ʜᴏʀɪᴢᴏɴᴛᴀʟ ᴄᴇɴᴛʀɪꜰᴜɢᴀʟ ᴘᴜᴍᴘ. and ᴡʜᴀᴛ ᴀʀᴇ ᴛʜᴇ ᴄᴜʀᴠᴇ ᴛʜᴀᴛ ᴀʀᴇ ɴᴏʀᴍᴀʟʟʏ ᴠɪꜱɪʙʟᴇ ᴏɴ ᴀ…

A: Horizontal centrifugal pump :

Q: A 90° elbow shown in Figure 5 (a) is to direct water flow upward at a rate of 50 kg/s. The water is…

A:

Q: Mr.Tariq wants to get material testing for his casting components where he doesn't want to damage…

A:

Q: Which of the following is NOT TRUE? Choose one: a. Even though a material has a Poisson's ratio of…

A: Introduction: Hooke's law states that "for tiny deformation, stress is exactly proportional to…

Q: how do i find, Vba; Vbc; Vbd?

A:

Q: What is the minimum pressure required to reduce volume of a brass sphere by 0.00003 %?

A: Given:reduction in volume=0.00003%

Q: Which modelling technique is suitable for modelling complex geometry?

A: The most suitable technique for modelling complex geometry is Wireframe modelling.

Q: a)Prepreg formation results in   Tape consisting of randomly oriented fibers Sheet consisting of…

A: Since you have posted multiple independent Multiple choice questions. We will solve the first…

Q: Q3/ Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A:

Q: What are the different systems of Units?

A: The different system of units are listed below: SI system MKS system FPS system CGS system The SI…

Q: 1. Figure shows a big pancake of hot plastic put onto the cold bed of a mold. After cooling, the…

A:

Q: Prepare at the process map for the manufacture of the cotton industry?

A: The steps in cotton mill , for the production of yarn from raw cotton- 1. Opening and cleaning 2.…

Q: What is rectification

A: Rectification is the conversion of alternating current to direct current. Rectification is performed…

Q: Q1- What is the theory of experiment? Q2- Define the spring? What kinds of the spring? Q3- Why the…

A: 1) The theory of the experiment would indicate the underlying principles that constitute the…

Q: What is the difference between normalizing process, annealing process, hardening process and…

A: Let us discuss in detail about normalizing,  annealing, hardening and Tempering processes.

Q: Seems incorrect setup, can you resolve?

A:

Q: How far from the lens must the film in a camera be, if the lens has a 32.0 mm focal length and is…

A: Given data as per question Object distance(u) =80 cm =800 mm Focal length(f) =32 mm  Here Location…

Q: Q3/A/ What is the type of the design for the following case? a) The miniature earphone b) fiber…

A: Given Models To find Type of design

Q: How did you determine the 63.2%

A: Given Data:   To Find: Generate a mathematical model from the given data.

Q: Using the answers from questions 14, 15, and 16, whatwould be the total heat gain due to the fresh…

A:

Q: Why will more heat be lost by the hot water than gained by the cold water?   a)Calorimeter will…

A: Option  B is correct  Calorimeter will absorb some of the heat.

Q: Dari gambar di atas gambarlah diagram bebas untuk semua batang. Kemudian carilah gaya reaksi tumpuan…

A: Given data  Given foce system.

Q: In sand casting process, the pattern is made of metal wood O plastic all of these

A:

Q: A calliper brake is required for the front wheels of a van with a braking capacity of 900 Nm for…

A: Given: The torque, T = 900 N.m The angle = 45 degrees The outer radius, R = 160 mm The inner radius,…

Q: Mr.Salman wants to get material testing for his casting components where he wants to damage his…

A: Mr. Salman wants to get material testing for his casting components where he wants to damage his…

Q: What do Olley's criteria state?

A: Statement of Olley criteria

Q: III. Calculations & Synthesis 1. Figure shows a big pancake of hot plastic put onto the cold bed of…

A:

Q: Q33) Write the appropriate names against the components shown in FIGURE 17 FIGURE 17

A: Solution: The names against the components are given below:

Q: I want a step by step working out on how all these values were obtained and what table was used

A:

Q: What is the force effect

A: The force effect.

Q: e area is smaller (d) their surface is

A: given: 1. The chemical potential (μ) of smaller size clusters is bigger than that of bigger size…

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.