Consider the leg shown, which is flexed to a right angle. The coordinates of the centers of gravity of the leg between the hip and knee joints (upper leg), the knee and ankle joints, and the foot, as measured from the floor level directly in line with the hip joint, are given in Table. The weights of the segments of the leg as percentages of the total weight W of the person are also provided in Table. Determine the location of the center of gravity of the entire leg. V1 Table Part x (cm) y (cm) W %) 17.3 51.3 10.6 2 42.5 32.8 4.6 3 45.0 3.3 1.7 Y3 Fig. Locating the center of gravity of a flexed leg

Consider the leg shown, which is flexed to a right angle. The coordinates of the centers of gravity of the leg between the hip and knee joints (upper leg), the knee and ankle joints, and the foot, as measured from the floor level directly in line with the hip joint, are given in Table. The weights of the segments of the leg as percentages of the total weight W of the person are also provided in Table. Determine the location of the center of gravity of the entire leg. V1 Table Part x (cm) y (cm) W %) 17.3 51.3 10.6 2 42.5 32.8 4.6 3 45.0 3.3 1.7 Y3 Fig. Locating the center of gravity of a flexed leg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

One of your employees is complaining of knee pain on the R. While assessing his workstation, you noted that from a sitting position (starting position: 90 deg flexion), the employee needs to exert a lot of effort to extend his right knee to 45 deg from the starting point. The length of the limb (from the tibial tuberosity to the heel area) is measured to be 38 cm. What now is the linear distance traveled by the limb from the initial position to 45 degrees of knee extension?
(d) A hydraulic actuator uses pistons of rectangular cross sectional area. The forcing piston dimensions’ equals to length= 4 cm and width = 5cm and the applied force equals to 200 N, what is the width of working piston that gives a working force equals to 3000 N as its length equal to 7 cm.
A bolt is being loosened by a 43 cm wrench by a force of 62N. The force makes an angle of 39° with the wrench. Find the torque.
Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to ride the seesaw, but the difference in their sizes, Joe weights 160lbs and Andy weighs 641lbs, makes this difficult. Joe sees a solution from his engineering class and moves the fulcrum from the middle to a new place. The seesaw is 3.5m long. After Joe moved the fulcrum how long was the seesaw on Joe's side?
Q2: A surface is tilt with horizontal 30o and has surface azimuth angle 10°. At May 5 in the local time 11 AM (Local latitude is 33.3), find the INCIDENCE ANGLE, 0. Ans:30.350 * * * * * *
If the water hp of a pump is 50 hp, the efficiency of the pump is 75%, and the efficiency of the motor is 90%, how many kw-hrs are consumed in one month’s operation? how many brake hp-hrs are consumed in one month’s operation? Answer should be 39,787 and 53,333. I need solutions thanks!!!
Find and solve at least 10 problems (5 easy and 5 hard) for Work and Energy
can you pls help me solve this.. I need to understand how it is solve for my review.. 1.) What is the theoretical horsepower requirement of a bucket elevator that is loaded down side with capacity of 545 kg/min and lift of 10.7 meters? •Pls answer in complete solution • provide a FIGURE (if applicable) Thank you! I'll give your answer a LIKE for helping me.
Make a problem where and object goes through three different energy changed. The oast change needs to be a situation where all the energy turns into spring potential energey. then solve
1. Do a project research based on this topic. Gas turbines are used for many purposes from aeroplane engines to industrial electric power generating sets. They are at the heart of most jet engines but also for propeller driven engines. Hence, do a mechanical report on operation for gas turbine plant and justify its operation.
The pulley below has a mechanical advantage of 3 and has a load of 300N assume an ideal pulley without friction losses, determine the following: a) what input force (input) do you apply to lift the load of 300 N? B) what is the tension in the 3 lines of the ropes of the pulley on the output side with the load as illustrated in the diagram? C) if the load is lifted to a height of 12 cm, how much rope is pulled on the input side d (in) in the diagram? D) how much work in joules (j) is required to lift the 300 N load 12 cm (0.12m)? E) how much power in watts (w) is required to lift the 300N load a distance of 0.12m in 20 seconds.
Can you solve this with steps?