Consider the following statements: 1-The effect of feedback is to reduce system error. 2-Feedback increases the system gain at one frequency but reduces the system gain as another frequency. 3-Feedback can cause an originally stable system to become unstable . Which of the above statements are correct? * O 1, 2, 3 1,3 O 2, 3 O 1,2

Consider the following statements: 1-The effect of feedback is to reduce system error. 2-Feedback increases the system gain at one frequency but reduces the system gain as another frequency. 3-Feedback can cause an originally stable system to become unstable . Which of the above statements are correct? * O 1, 2, 3 1,3 O 2, 3 O 1,2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(2) ukäi Q) In the negative feedback, which of the following * .statement is true (a) Gain, noise, distortion as well as the bandwidth of the amplifier are decreases. (b) The feedback is out of phase with their input signal and the the gain stability decreases. (c) It is called regenerative and used in amplifiers. (d) The input voltage is reduced and the input and output impedances are improved.
Use nodal analysis to find the voltage V in the circuit given below, where v = 144/15°V. 40 92 www j20 22 m Vs +1 0 = 6/30° A Please report your answer so the magnitude is positive. The voltage V = Vm 20 V, where: Vm V V (Calculate to 2 decimal places) deg (Calculate to 2 decimal places) -j30 Ω 50 92
Please show the complete solution and necessary figure. Thank you!
One of the disadvantage of negative feedback loop is lag caused because it can only be exerted after controlled variable has been disturbed. In order to minimize lag between a change in a controlled variable and the action of the effector, it is advantageous for the body to anticipate any likely change. Which one of the following physiological mechanism achieves this? Select one: O a. Feedbackward control O b. Feedforward control Positive feedback control C. O d. All of the above e. None of the above
Figure 3 shows a Hartley oscillator. Assume that the op-amp employed in the figure is an ideal op-amp, and R1= 20 kΩ, R2 = 60 kΩ, L1=10 mH. b) State the Barkhausen criterion for sustained oscillation.c) Explain briefly how the phase shift requirement for sustained oscillation ismet in the circuit of Figure 3.d) The feedback ratio and oscillation frequency of Figure 3 are givenrespectively by, B = -L2/L1 and w0 = 1 / sqrt(L1 +L2)C Determine the values of C and L2 in order for the circuit to oscillate at a frequency of 200 Hz.
A system has a gain of 80 db without feedback, if the negative feedback is 1/50th. What is the closed loop gain of the system in db with the addition of the negative feedback?
1- Static synchronous compensator (STATCOM) for powe factor improvement. 2- What is penalty factor? Derive the expression for the penalty factor in economic load dispatch.
68. A negative voltage feedback amplifier has voltage gain without feedback, A, = 1000 and feedback fraction m = 0.01. If the lower cutt-off frequency f₁ = 1.5 kHz and upper cut-off frequency f₂ = 501.5 kHz before feedback, what is the value of lower cutt- off frequency after negative feedback? (i) 1.5 kHz (ii) 272.8 Hz (iii) 136.4 Hz (iv) 3 kHz 69. In Q 68, what is the value of upper cut-off frequency after negative feedback? (1) 501.5 kHz (iii) 2006 kHz (ii) 1003 kHz (iv) 5.52 MHz
Q:: Read each statement carefully and answer by True or False (if False then, correct the statement). 1- Decrease the derivative time to reduce the effects of noise on feedback. 2- In the process systems, the integrator variables are always to be controlled because the integrators are unstable. 3- It is required to do a data validation before proceeding wiun une vmp.. modelling procedure. 4- Without a measurement filter, the noise does not go "around and around" in the feedback loop. 5- Feedforward control affects the stability of the Feedback control system when they are used together. 6- The statistical method has more calculations than process reaction curve method IIl when finding the empirical model.
Consider the system in Figure below, K is a positive parameter is the controller gain, and a is a parameter. D R 1 Y K(s+a) (s + 2)(s +3)(s + 1) a. At which condition the system above is stable? b. Can you find one or more situation in which the feedback system is always stable? c. How would you select a so that the system behaves exactly as a second order system with the fasted response possible? Justify your answer. d. Select K in a way that the system overshoot does not exceed 5%.
Electrical Engineering - Electronic ll Please solve the question quickly
1-For the ramp input, the steady state error of the control system (Type one) is: a) zero b) A/K c) infinite d) none of the them 2- After moving the pick-off point (as shown in the figure), The feedback transfer function will be equal to : R(s)- a) H₂G, /a) 1 b) H₂/G₁ G₁ b) 2 nos H₁ 3- For the root locus plot, the number of the asymptotes for the following system are: G(s)H(s) = c) 3 H₂ c) H₂+G₁ K a) 1