Consider the following simply supported beam. It has normal-weight concrete with a compressive strength of 5,000 psi and Grade-60 bars. Each support is 12 in. wide. The section is a hollow box. The beam is to carry a uniformly distributed dead load of 2.5 kips/ft., including its own weight. The live load is a point load of 60 kips, located at mid-span. Total dead load including self- weight = 2.5 kips/ ft. 12 in. 12 ft. PL= 10 kips 12 ft. #3 stirrup 5 in. 17 in. 5 in. 4 in. 20 in. 12 in. 14 in 24 in. For shear reinforcement, #3 stirrups are to be used. The area of a single #3 bar is 0.11 in.2. Determine the spacing of the stirrups according to ACI 318? Drawing the arrangement of the stirrups in a diagram.

Consider the following simply supported beam. It has normal-weight concrete with a compressive strength of 5,000 psi and Grade-60 bars. Each support is 12 in. wide. The section is a hollow box. The beam is to carry a uniformly distributed dead load of 2.5 kips/ft., including its own weight. The live load is a point load of 60 kips, located at mid-span. Total dead load including self- weight = 2.5 kips/ ft. 12 in. 12 ft. PL= 10 kips 12 ft. #3 stirrup 5 in. 17 in. 5 in. 4 in. 20 in. 12 in. 14 in 24 in. For shear reinforcement, #3 stirrups are to be used. The area of a single #3 bar is 0.11 in.2. Determine the spacing of the stirrups according to ACI 318? Drawing the arrangement of the stirrups in a diagram.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6.
A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
Question 25 An axially loaded tied column must sustain the following service loads: Total Dead Load 1,000 kN = 1,600 kN Required Strength, U = 1. 2D + 1.6L Live Load Reduction Factor 0.65 Concrete f'c Steel fy 21 MPa 420 MPa Determine the size of a square column (mm) using an 3% vertical bar steel ratio. 400 500 550 450
I need the answer to the question in reinforced concrete
I need the answer to the question in reinforced concrete
Ultimate Design Single concrete
The dimensions for a reinforced concrete beam are given as: b = 300mm d = 400mm d’ = 75mm It is to be designed for a service dead load moment of 30kN-m and a service live load moment of 40kN-m. Suppose f’c = 21MPa and fy = 276MPa, how many 20-mm bars are required to reinforced the beam in terms of steel area?
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
A 15 x 25 in. column is reinforced with four No. 9 (No. 29) bars, one in each corner as shown in Figure (a). The concrete cylinder strength is f. = 4000 psi and the steel yield strength is 60000 psi. Determine the axial load strength for zero eccentricity without subtraction of the concrete displaced by the steel, as well as with subtraction of the concrete displaced by the steel. E=0.003, E,-29000. Imperial Metric bar Linear Mass Density Nominal diameter Nominal area 25" bar size size (soft) Ib (in) (mm) (in') (mm") 2.5" -2.5" 0.250 - % 6.35 0.05 32 0.375 = % 9.53 0.11 71 0.500 = 4 12.7 0.20 129 0.625 = % 15.9 0.31 200 0.750 = % 19.1 0.44 284 0.875 = % 222 0.60 387 1.000 = % 25.4 0.79 510 1.126 - % 28.7 1.00 645 1.270- 1% 32.3 1.27 819 No.6 0.167 0.249 3 No. 10 0.376 0.560 #4 No. 13 0.668 0.994 Pn #5 No. 16 1.043 1.552 15" No. 19 1.502 2.235 #7 No.22 2.044 3.042 #8 No 25 2 670 3.973 As No 29 3.400 5.060 A's #10 No 32 4.303 6.404 e varies #11 No.36 5.313 7.907 1.410- 35.8 1.56 1.006…
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
AT-Beam has the following properties: bf = 750 mm, bw = 275 mm, d 560 mm, t = 115 mm. Concrete compressive strength fe 21 MPa and steel yield strength fy 415 MPa. T-Beam is under factored moment load of 720 kN-m. Locate the compression block under balanced condition from the extreme compression fiber.