Answered: Consider the following schematics. (1)…

Consider the following schematics. (1) What is the dynamic order of this network? Explain your answer. (2) Derive the transfer function from Vi to Vo +1 C1 500 nF Vi C2 500 nF R1 100 kQ Vo+ Vo-

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The output voltage, Vo, is given by Rf R2. Vo R1 V1 (N R3 Select one: RF RF + V1 R2 || R3 V2 a. Vo R1 R3 O b. V, = R2+RF R2 RF V2 R2 R,+R3 O c. none of the mentioned 2 RE RF V2 O d. V. = - R, R1.R3
The summer you have designed has four input lines with R1=1, R2=1/2, R3=1/4, R4=1/8and Rf=1, all values given in kΩ. The input lines are set at 0 B6 or 1v. Find V0 in terms of the following set of input values V4=1, V3=0, V2=0 and V1=1
2) Answer to the following three parts. You can use KVL/KCL or simply use the techniques we reviewed in class. the input a. For the circuit shown below, determine the voltage gain (Aa=Vol/Vini). resistance Ignore ro's. and the output resistance R2 = R5 = R 1 R3 = R4 = R6 = 10R B = 100 %3D %3D (R1 =0.1R = 0.1R Assumptions: Im2 9m1 Qz Vini Ri Ru Ru RS R2 Rin I RoutI o Voi Vinl C2-a
1. Find the closed loop transfer functions for the following block diagrams R(s) 50 C(s) Figure 1: Problem (1-a) D R (s) C (s) B H G Figure 2: Problem (1-b) H(s) R(s) G (s) G2(s) + C(s) Figure 3: Problem (1-c)
What is the order of this instrument and find the transfer function of the Q2-) system below where Vi is the input and Vo is the output? Draw the output Vo for the given unit step input u(t) + 1 kO + Vo 10 ko 1 µF u(t) (JU) A wheatstone bridge is used to measure the temperature using a thermistor at the resistor branch Rx. R1=R3 and R2 is adjustable by a potentiometer. Rx is the resistance of the thermistor. At the room temperature of 300K, the bridge is balanced (voltage over G=0) by setting R2 to 1k2. If the material constant B for the thermistor is 3000, at the temperature of 400K what should be the new R2 value to balance the bridge? Q3-) A R, Rs E De G В R, Rx +
Question 1: a) Sketch Vo versus time for the circuit shown with the input given. b) Determine DC output voltage without a capacitor. c) If a capacitor of 10 uF is placed in parallel with RL, sketch the vo versus time. d) find the DC output voltage. Given R1 = R2 = RL = 2.2 k2. Vi +40 D1. D2 10 ms R = 2.2 k2 ww R%3D 1GF R = -40 2.2 k2 2.2 k2
M.C.Q Q.In the non-inverting configuration of operational amplifier The positive terminal is connected to the ground directly The negative terminal is connected to the power source The positive terminal is connected to the power source The negative terminal is connected to the ground directly
For the circuit shown below, assume re = 130, VCC (in V) is: VCC 2k 92k 4k luF luF 4k Vin luF S-99 luF o Vo 0.5k 0.5k 1uF O 9.7 O 10.7 O 11.7 O 7.7 O 6.7 O 8.7 For the circuit shown below, assume re 13 2, the input impedance Zin (in k2) is: VCC 2k 92k 4k luF luF 4k Vin luF B=99 4k luF Vo 0.5k 0.5k luF O 17.53 О 22.79 O 53.92 O 42.87 O 34.53 O 9.43 HH
Use source transformation to find the output current loin the circuit given below, where V₁ = 40 30° V, XL = 50 2₂ Xc= 2002, R₁ = R₂ = 80 02, and V2 = 100 V. Please report your answer so the magnitude is positive and all angles are in the range of negative 180 degrees to positive 180 degrees. jXL V₁ R₁ www R₂ www -jXc The output current in the given circuit is V₂ °A.
2. Obtain the transfer function X o(s)/Xi(s) of the mechanical system shown in Figure (a). Also obtain the transfer function Eo(s)/Ei(s) of the electrical system shown in Figure (b). Show that these transfer functions of the two systems are of identical form and thus they are analogous systems. wwwwww b₂ ww (a) b₁ S (b) C₁ www HE
If VGSQ = 7 V, C1 = 26 nF and C2 = 46 nF in the circuit in the figure, what is the low cut-off frequency of the system? NOTE: rd will be taken into account in calculations.
The following lead compensator is designed to obtain the desired closed-loop pole at (-2 + j2). Determine the gain Kc of the compensator. R(s) s+1 s+3 K s+5 s(s +1) plant en lead compensator Select one: O a. 4.56 Оь. 1.55 Oc 2.78 O d. 3.67 O e. 6.40