Consider the following design problem concerning implementation of virtual-circuit service. If virtual circuits are used internal to the subnet, each data packet must have a 3-byte header and each router must tie up 8 bytes of storage for circuit identification. If datagrams are used internally, 15-byte headers are needed but no router table space is required. Transmission capacity costs 1 cent per 106 bytes, per hop. Very fast router memory can be purchased for 1 cent per byte and is depreciated over two years, assuming a 40-hour business week. The statistically average session runs for 1000 sec, in which time 200 packets are transmitted. The mean packet requires four hops. Which implementation is cheaper, and by how much?

Consider the following design problem concerning implementation of virtual-circuit service. If virtual circuits are used internal to the subnet, each data packet must have a 3-byte header and each router must tie up 8 bytes of storage for circuit identification. If datagrams are used internally, 15-byte headers are needed but no router table space is required. Transmission capacity costs 1 cent per 106 bytes, per hop. Very fast router memory can be purchased for 1 cent per byte and is depreciated over two years, assuming a 40-hour business week. The statistically average session runs for 1000 sec, in which time 200 packets are transmitted. The mean packet requires four hops. Which implementation is cheaper, and by how much?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: What takes happen if a processor makes a request that cannot be satisfied by the cache while it is…

A: When a processor requests data, the cache is the first place that is checked for the requested data.…

Q: Assume two hosts, A and B, that are linked by a single link with a rate of R bps and are spaced m…

A: Sure, let's break down the questions step by step and calculate the values.Rate of the link (R) = R…

Q: Eight data terminals statistically share the capacity of an outgoing link. Traffic is combined from…

A: The Handwritten Solution is given below:

Q: Problem 3 Consider the problem of deciding whether to implement a virtual- circuit or a datagram…

A: Answer: a) packets arrive periodically= L/R L-packet size R- rate. 256/9600=0.026. b) The…

Q: Consider a TCP connection with the following parameters: a) Initial ssthreshold = 4 segments b)…

A: Q1 Answer:- We have the given data: Initial ssthreshold = 4 segments Round Trip Time (RTT) = 10…

Q: as a possible congestion control mechanism in a subnet using virtual circuits internally, a router…

Q: A TCP PDU of length 40,513 octets (including the TCP header) is to be transmitted over a physical…

A: To calculate the number of bits sent over the connection from the source to the destination, we need…

Concept explainers

Network transmission cabling

A network is a collection of devices connected by communication links. A device can be a computer or any instrument capable of sending and receiving data or information formed by other nodes toward the network. A channel that connects people or things is known as a network. It sends the data from one place to another. It is the basic concept of a computer, network, and data communications.

Question

Consider the following design problem concerning implementation of virtual-circuit
service. If virtual circuits are used internal to the subnet, each data packet must have a
3-byte header and each router must tie up 8 bytes of storage for circuit identification. If
datagrams are used internally, 15-byte headers are needed but no router table space is
required. Transmission capacity costs 1 cent per 106 bytes, per hop. Very fast router
memory can be purchased for 1 cent per byte and is depreciated over two years,
assuming a 40-hour business week. The statistically average session runs for 1000 sec,
in which time 200 packets are transmitted. The mean packet requires four hops. Which
implementation is cheaper, and by how much?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Assume a 10Mbps Ethernet has two nodes, A and B, connected by a 360m cable with threerepeaters in between, and they each have one frame of 1,024 bits to send to each other. Further assumethat the signal propagation speed across the cable is 2*10^8 m/sec, CSMA/CD uses back-off intervals ofmultiples of 512 bits, and each repeater will insert a store-and-forward delay equivalent to 20-bittransmission time. At time t=0, both A and B attempt to transmit. After the first collision, A draws K = 0and B draws K = 1 in the exponential back-off protocol after sending the 48bits jam signal. a. What is the one-way propagation delay (including all repeater delays) between A and B inseconds? At what time is A's packet completely delivered at B? b. Now suppose that only A has a packet to send and that the repeaters are replaced with switches.Suppose that each switch has an 8-bit processing delay in addition to a store-and-forward delay.At what time, in seconds, is A's packet delivered at B?
Consider the subnet in Fig. 3.11.5. Distance vector routing is used and the following vectors have just come in to router C: from B (5, 0, 8, 12, 6, 2); from D(16, 12, 06, 0, 9, 10) and from E(7, 6, 3, 9, 0, 4). The measured delays to B, D and E are 6, 3 and 5 respectively. What is C's new routing table? Give both the outgoing line to used and the expected delay ? A B E Fig. 3.11.5 F D
We define data link layer communication efficiency as the ratio between a packet transmission time and the sum of the the packet transmission time and twice of its propagation time. A channel has a bit rate of 10 kbps and a propagation delay of 10,000 micro-second. For what range of frame sizes (in number of bit) does stop-and-wait give an efficiency of at most 90%?
Consider a TCP connection with the following parameters: a) Initial ssthreshold = 4 segmentsb) Round Trip Time (RTT) = 10 millisecondsc) Timeout period = 40 millisecondsd) Segment size = 3900 bytesThe TCP connection was used to transfer 17 data segments. While sendingthe segments, data segment 7 and data segment 15 were lost the first timethey were sent (but arrived at the receiver properly when retransmitted).There were no other segment losses apart from the aforementioned. Assumethat data segments received out-of-order are buffered at the receiver. Whatis the average throughput obtained in sending all the data segments (inbytes/sec) including draw a diagram to show the communication process in detail.
Consider a full-duplex 512 kbps link with length 36,000Km connecting two hosts. The data frames carry a useful payload of size 6000 bits. Assume that both ACK and data frames have 400 bits of header information, and that ACK frames carry no data. The propagation speed along this link is 3×108 m/sec. a) What is the RTT on this link? b) What is the effective useful data throughput, in kbps, when using Stop-and-Wait?
A TCP connection is established through 10 wireless hops in an acoustic underwater ad hoc network. Assume that each hop is 100 meter in the average, acoustic signals travel 1500 meter per second, 10 kilobit data can be sent per second over a link, the source node has one megabyte of data to send, the receiver window size is 64 kilobytes, the maximum segment size is 1 kilobyte and the average processing delay for routing at each node is one millisecond. Assume also that the following segments do not reach the destination: 67, 112, 137. What would be the average utilization of the links for this connection if there is not another communications through them? Explain an alternative approach to increase the bandwidth utilization?
In a two-phase, total-order multicast system, messages are sent in the following sequence from node S to G1 and G2. G1 and G2 are the members of the group. S sends m1 to G1 S sends m1 to G2 S sends m2 to G2 S sends m2 to G1 Use the basic implementation of the Lamport clock. The clock s at each node start at: S: 4, G1: 6, G2: 1. Show the exchange of messages and their acknowledgments in a clock diagram using the basic implementation of Lamport's clock. In which order and at what times are m1 and m2 delivered?
What does the term "connection status information" imply in the context of a virtual circuit network, and what does it represent? The forwarding database of a switch must be updated at the same rate as it generates and removes connections in a VC network, which is one connection every millisecond (on average).