Consider the following conditions: Condition I Condition 2 A wooden cube of size 2 m and the 20% of the volume of a body is visible relative density of 0.5 floats in the over the free surface of the water. water. Calculate: (i) Volume of the cube submerged in the water, based on Condition 1. (ii) Density of the wooden cube, based on Condition 2.

Consider the following conditions: Condition I Condition 2 A wooden cube of size 2 m and the 20% of the volume of a body is visible relative density of 0.5 floats in the over the free surface of the water. water. Calculate: (i) Volume of the cube submerged in the water, based on Condition 1. (ii) Density of the wooden cube, based on Condition 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is shown. At an initial temperature of Ti = 22°C, the outer diameter of the disk is D = 210 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 24 mm. At a final temperature of Tf = 46°C, determine:(a) the change in diameter Δd of the central hole (assume an increase Δd as positive, otherwise as negative).(b) the change in thickness Δt of the disk (assume an increase Δt as positive, otherwise as negative).(c) the normal strain in the circumferential direction around the outside of the disk.
The relationship between the relative density and the angle of friction
A cylinder of 100 cm height and uniform diameter 'd' floats in water with its axis in vertical position. If the specific gravity of the cylinder material is 0.6, then the minimum permissible value of the diameter so that the cylinder remains in stable equilibrium condition is cm.
The surface tension of mercury at 60°C is 0.47N/m. What capillary height in mm will occur in this fluid whe in contact with a glass tube of radius 0.3mm? Use 130° for mercury. O 11.5mm fall O 11.5mm rise O 15.1mm fall O 15.1mm rise
For a nonwetting liquid, such as water, the surface is convex since the force of cohesion will be greater than that of adhesion. Water is non-Newtonian. Temperature at which water has the highest density is usually taken as 4°C(39.2°F). PROBLEM 1: A closed tañk whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. a. Determine the pressure at the interface of carbon tetrachloride and syrup. * Your answer b. Determine the difference in pressure between the interface of water and syrup and the interface of carbon tetrachloride and syrup.
For many applications, it is accurate enough to treat water as incompressible. But for a more detailed understanding of fluid flows, compressibility must be taken into account. Fortunately, the bulk modulus of water is close to constant, so let's model the pressure in a motionless water column assuming that the bulk modulus is a constant, K, = 2.1 GPa. The pressure and density at the top surface of the water column are 6. Po =1000 hPa and P, =1000 kg/m², respectively, and the downward acceleration due to gravity is g =9.8 m/s. Take depth, z, to be positive downward with z = 0 at the top %3D %3D %3D surface. Using the definition of bulk modulus, derive an expression for the density field, p, in terms of pressure, p, and the given parameters. Leave all parameters а. as algebraic. (At this point, your expression should not include z .) b. Starting from hydrostatic balance and the expression in part (a), derive an expression for the pressure field, p(z), in terms of z and the given…
A copper (SG=8.8) cylinder of diameter 4 cm and length 15 cm weighs only 14 N when submerged in liquid. Determine the liquid density.
Specific Gravity =(W_(S))/((W_(SSD)-W_("submerged "))) Explain how (W_(SSD)-W_("submerged ")) represents the "weight of an equal volume of water".
Question #1 A hole having a diameter of 75 mm is cut out from a uniform plate of diameter 240 mm. The distance between the center of the plate and center of the hole is 50 mm. Determine the position of the center of gravity of the remaining material.