Consider the circuits below with the following nominal values: Vz = 6.8 V kamn) - 2 mA Input voltage = 12 *1 volts. Maximum load current is 90 mA Minimum load current is 10 mA a) Describe the operation of Circuit A. What is the function accomplished? b) Determine the value of R to always maintain the Zener turned on (Circuit A). c) Evaluate the maximum current and maximum power of the Zener (Circuit A). e) Analyze Circuit B assuming the same parameters and components used in Circuit A. Describe the operation of the circuit clearly, and use Multisim to support your arguments. Vin o Vout R Rjoad R OV out Vin Rjoad CIRCUIT B CIRCUIT A

Consider the circuits below with the following nominal values: Vz = 6.8 V kamn) - 2 mA Input voltage = 12 *1 volts. Maximum load current is 90 mA Minimum load current is 10 mA a) Describe the operation of Circuit A. What is the function accomplished? b) Determine the value of R to always maintain the Zener turned on (Circuit A). c) Evaluate the maximum current and maximum power of the Zener (Circuit A). e) Analyze Circuit B assuming the same parameters and components used in Circuit A. Describe the operation of the circuit clearly, and use Multisim to support your arguments. Vin o Vout R Rjoad R OV out Vin Rjoad CIRCUIT B CIRCUIT A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a full-wave bridge rectifier equivalent DC output voltage circuit, calculate the effective DC voltage output given a Vin(RMS)=110 V (60 Hz) and the turns has a ratio of 10:1. Explain each step of your calculation briefly.
B. Design a Clamper circuit to produce the given output waveform with output voltage of V1= 5.7 volts and V2= - 34.3 volts. Input voltage is Vin = 20 Volts and Silicon diodes is used. Silicon diodes Vin V1 Design -Vin -V2
Q4 / three phase half wave controlled rectifier is used to feed a resistor load of ( 10 ohm) the source is (208 volt) star connected: calculate: 1- The average value of the voltage and current on the terminal load if angle (45). 2- The average of the voltage on the terminal load if angle (80). 3- The angle required to get 7 amp. 4- Draw the circuit.
Two same size PV Modules are connected in Parallel. The specification of each module is given as, Number of cells = 36, Area of each cell is 12 cm x 12 cm. Assume the necessary data. Refer to the above PV Panel choose the correct statement. a. The output current of each PV Module is 2.15A b. The output current of each PV Module is 8.6A c. The output current of each PV Module is 4.3A d. The output current of each PV Module is 1.25A
I need answer within 5 minutes please please with my best wishes
Ripple factor is more for bridge Rectifier. Select one: True False
Q3: bridge rectifier circuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=xo for a reverse bias. The input voltage of the circuit is 240V and 482 load resistance. Determine: The de load current, the power input efficiency and the PIV rating is required for the diodes. D4 D1 Rd=10 RL=480 Vs Vrms Vo D3 D2 Figure 1
A de-de converter is to be built to the following specifications: Allowed de input voltage range: +3 V to +18 V Output voltage (average value): +24 V Output voltage ripple: ±0.05 V maximum at rated load Rated load: 120 W, resistive Input current ripple: ±100 mA maximum at rated load Switching frequency: 100 kHz Common ground between input and output a. Draw a circuit which can perform this function. How many switches have gates? b. What is the range of duty ratio values for each switch? c. Find circuit part (L, C, R) values which will meet the stated specifications.
Q3: For the circuit below determine: 1. Name of the cct. 2. Determine and draw (Vo), also its dc – level. (all diodes are Si) Vi D2 D1 20 Vi Vo 21 -20 D3 D4
6. Given the number 0XA0BOCODOE0F0, a. How many bytes for this number b. How many bits for this number c. Store in 8-bit computer with little endian system, and the starting address is 0x123, please show thedata memory map d. Store in 8-bit computer with big endian system, and the starting address is 0x123, please show the data memory map
A half-wave rectifier with a reservoir capacitor is connected to an AC mains supply(220Vrms, 50Hz) via a 20:1 transformer. What value of the capacitor is needed forthe ripple voltage of X% of the peak input voltage? The load takes a maximum currentof ???? mA. X= 12% mA = 160
Q4. For the three-phase fully-controlled bridge rectifier circuit shown with purely resistive load: a = 90° a. Sketch the output voltage waveform. a b. Determine the ripple factor. VA= 240 V RL 752 CB A-B A-C B-C B-A CA C-B a Vc 27