RLV.2Figure 1. Single-phase capacitor-fi Iter rectifier circuit.本 Análisis de rectificador onda completaConsider the capacitor-filter rectifier circuit as shown in Figure 1. The input is a single-phase source that is derived from a 220 Vrms mains. Tasks for analysis:(a) Rig up the circuit as shown in Figure land plot V; and i versus time.(b) Why is there ringing on the current wave-form?(c) What is the series impedance of the circuit?(d) Plot Vi and Vo versus time. What is the ripple? How does ripple depend on load, capacitor C, and frequency of input wave-form?(e) Measure the current and voltage waveform across the rectifier diode(f) Estimate the average and rms currents through the rectifier diode. Calculate the diode power dissipation.(g) What should be the peak current rating of the diode?(h) Change the initial charge voltage on the capacitor Ct. What is the effect on the input surge current?(i) Change the phase angle of the input Vi at start up. Observe the effect on current i. What happens and why?(i) Under what conditions do you get maximum peak current to flow through the diodes?(k) Measure the input voltage and current and estimate the power factor.(1) What is the effect of change in C value on the input current and power factor?Vour analytic results.

There is nothing mentioned about the diode , so we will take the diode as ideal one, i.e no voltage…

Consider the capacitor-filter rectifier circuit as shown in Figure 1. The input is a single-phase source that is derived from a 220 Vrms mains. Tasks for analysis: (a) Rig up the circuit as shown in Figure land plot Vi and i versus time. (b) Why is there ringing on the current wave-form? (c) What is the series impedance of the circuit?

Consider the capacitor-filter rectifier circuit as shown in Figure 1. The input is a single-phase source that is derived from a 220 Vrms mains. Tasks for analysis: (a) Rig up the circuit as shown in Figure land plot Vi and i versus time. (b) Why is there ringing on the current wave-form? (c) What is the series impedance of the circuit?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
5
Creating buck-boost converter diagram using the following: Voltage: 12V-5V The diagram includes voltage regulator.
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
4- Single phase centre-tape rectifier with 100V peak secondary voltage per coil, energizing 10 Ohms and 2mH inductance with 50Hz source. The output rectified voltage drops to ...of the Vdc. *
Q4: Calculate (1) the percentage ripple, (2) the regulation, and (3) the optimum number of stages (4) The maximum voltage of 12- stages Cockcroft-Walton type voltage multiplier with capacitances equal to 1200 nF. The peak supply voltage is 400KV with frequency equal to 60 Hz. and load current to be drawn is 10 mA
Explain the working of single phase full converter for RLE load discontinous mode o operation with neat sketch, waveform and equations.
What is easier to smooth single-phase or three-phase rectifier circuits? And why?
1) a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two ac outputs and calculate turns ratio of live transformer. voltage i) 10 V ii) 100 V 2) b) Consider a circuit using Si diodes and 10 k ohms resistors. Design this clipper circuit with output ranges below; i) -0.7 V and above ii) +2.1 V and above iii) +1.4 V c) As given in the figure a clamper circuit with the input +10V- signal Vi is proposed to design. Determine the output voltage with the exact solution step by step. Sketch transfer characteristic Vo versus V₁. V₂ Vo H 2RS -10V- -2√ 01 Vo Trims
How to create a voltage converter from AC to DC using Diodes and capacitors?
Explain the operation of a full-wave voltage quadrupler circuit (With proper explanation, equation, and diagram of each cycle).
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.