Consider the beam with overhanging ends loaded by the three concentrated forces shown in Fig. The beam is simply supported and is of T-type cross seetion as shown. The material is gray cast iron having an allowable working stress in tension of 35 MPa and in compression of 150 MPa. Determine the maximum allowable value of P.

Consider the beam with overhanging ends loaded by the three concentrated forces shown in Fig. The beam is simply supported and is of T-type cross seetion as shown. The material is gray cast iron having an allowable working stress in tension of 35 MPa and in compression of 150 MPa. Determine the maximum allowable value of P.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

D esign and draw a cottered joint to join two rods safely to resist a load of 60 kN that acts along the co - incident axes of the rods connected by the cotter. The material of the cotter and the rods will permit the following safe stresses tension = 60 MN / m², crushing = 100 MN / m² and shear = 50 MN / m².
A 12” X 16”simply supported pine wood beam is being considered to carry a uniform load distribution across a span of 12’ as shown. In addition to the uniform load, the beam is also subjected to a tensile load of 20 kips. If the ultimate tensile stress in pine wood is 4500 psi, determine whether the beam is considered safe according to the Allowable Stress Method, using a Factor of Safety 2.5. Hint: you can calculate the maximum tensile stress in the cross-section without having to use Mohr’s circle
A flat steel bar, 26 mm wide by 5 mm thick and 1.2 m long, is bent by couples applied at the ends so that the midpoint deflection is 28 mm. Compute the maximum stress in the bar. Use E 220 GPa. Answer must be in MPa.
A square hollow bar has a breadth and depth of 30mm and a wall thickness of 2mm. A tensile force of 120KN is applied at the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line.
Problem # 1: For the trussloaded as shown, calculate the axial stress developed in members CD, ND and NK.Use A=20in2. ( 15 t 15 ft 111 920 lb 1145 lb 1760 lb -20 it20 n 20 t20n-201-20 t-
The figure shows a round shaft from a gear transmission. Gears are mounted at points A, C, and E. Supporting bearings are at B and D. The forces transmitted from the gears to the shaft are shown, all acting downward. Compute the maximum stress due to bending in the shaft, accounting for stress concentrations. Draw shear diagram and moment diagram. calculate the safety factor for the material selected. The material is 4150 OQT 1300. Assume that f1 = 9.5 KN , f2= 13.5 KN and f3 =18 KN
Problem 3: A hot rolled steel shaft is subjected to a torsional load that varies from 3000 in-lb clockwise to 1000 in-lb counterclockwise as an applied bending moment at a critical section varies from + 4000 in-lb to 2000 in-lb. The shaft is of uniform cross section and no keyway is present at the critical sec- tion. Determine the required shaft diameter. The material has an ultimate strength of 80,000 psi and a yield strength of 60,000 psi. Base design on a factor of safety N=1.5. Take the endurance limit as half the ultimate strength.
Solve following the problems below and show your complete, systematic and neat solution. Upload your solution with one PDF file. 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural stress of the fiber located at 3m from the left support and 50 mm above the bottom 18 kN/m 300 mm 6 kN/m 20 mm 27 kNm 22 2m 2m 3 m +m 15 mm - - 50 mm 360 mm 20 mm
A 28 mm diameter rod with a 30 mm diameter handle as shown in Figure Q1 has two 90 degree bends. The handle is attached to the wall at 'A' while 1.8kN load is applied at the end of the rod at 'E'. Calculate Maximum Shear Stress at location 'A' and 'B' and determine it critical location. Bending load at point 'A'? Bending load at point 'B'? (Nm) Torsion load at rod; 'T'? Normal Stress due to bending load at point 'A'? (MPashear Stress due to torsion load at point 'A'? (MPa) 1st Principle stress at point 'A' (max principle stress)? (MPa Maximum shear stress at point 'B'? Critical Location? (L1) 170 $30- (L2) в 470 $28- F= 1.8kN| E 300 100 (L3) D Figure Q1
Kindly show your complete handwritten solution. Answers in mm.