Solve it fast please i give thums up Consider the beam shown in (Figure 1). EI is constant.Figure-2a< 1 of 1 >Part ADetermine the equation of the elastic curve for the part of the beam 0 < x < a using the #₁ coordinate.Express your answer in terms of some or all of the variables x₁, a, P, E, and I.Η ΑΣΦv1 =SubmitPart B1/2 =SubmitDetermine the equation of the elastic curve for the part of the beam a < x2 < 3a using the ₂ coordinate.Express your answer in terms of some or all of the variables x2, a, P, E, and I.ΜΕ ΑΣΦPart CRequest AnswerVmax=SubmitRequest AnswervecRequest Answer?vecSpecify the beam's maximum deflection.Express your answer in terms of some or all of the variables a, P, E, and I. Enter positive value if thedisplacement is upward and negative value if the displacement is downward.- ΑΣΦΙΠ1 | vec 3??

Consider the beam shown in (Eigure 1). EI is constant. Figure < 1 of 1 > Part A Determine the equation of the elastic curve for the part of the beam 0<< using the coordinate. Express your answer in terms of some or all of the variables 2₁, a, P, E, and I. —| ΑΣΦ. 11. vec v1 = Submit Part B Determine the equation of the elastic curve for the part of the beam a< x₂ < 3a using the coordinate. Express your answer in terms of some or all of the variables x2, a, P, E, and I. 1/2 = Submit Part C Request Answer Umax= Η ΑΣΦΙΚvec Request Answer Specify the bear's maximum deflection. Express your answer in terms of some or all of the variables a, P, E, and I. Enter positive value if the displacement is upward and negative value if the displacement is downward. 17 ΑΣΦ ? vec ?

Consider the beam shown in (Eigure 1). EI is constant. Figure < 1 of 1 > Part A Determine the equation of the elastic curve for the part of the beam 0<< using the coordinate. Express your answer in terms of some or all of the variables 2₁, a, P, E, and I. —| ΑΣΦ. 11. vec v1 = Submit Part B Determine the equation of the elastic curve for the part of the beam a< x₂ < 3a using the coordinate. Express your answer in terms of some or all of the variables x2, a, P, E, and I. 1/2 = Submit Part C Request Answer Umax= Η ΑΣΦΙΚvec Request Answer Specify the bear's maximum deflection. Express your answer in terms of some or all of the variables a, P, E, and I. Enter positive value if the displacement is upward and negative value if the displacement is downward. 17 ΑΣΦ ? vec ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
Solve it quickly please now
Please help answer all parts, thanks
I need accurate answer
Please answer immediately thank youuuu
MENG364 MANUFACTURING TECHNOLOGY please solve the question very quickly Student Number 124544
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
solve 30-40 minutes hand written asap..i'll give you multiple upvote
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Can someone please help to solve this question following the directions and showing neat work and formulas and drawing all needed diagrams. PLEASE AND THANK YOU!!!
Can you please do the same problem but show the work better its hard to follow steps