Consider the automobile hydraulic system shown in Figure. Suppose a force of 100 N is applied to the brake pedal, which acts on the pedal cylinder (acting as a "master" cylinder) through a lever. A force of 500 N is exerted on the pedal cylinder. Pressure created in the pedal cylinder is transmitted to the four wheel cylinders. The pedal cylinder has a diameter of 0.500 cm and each wheel cylinder has a diameter of 2.50 cm. How much pressure is transmitted in the hydraulic system? Express your answer in atmospheres.

Consider the automobile hydraulic system shown in Figure. Suppose a force of 100 N is applied to the brake pedal, which acts on the pedal cylinder (acting as a "master" cylinder) through a lever. A force of 500 N is exerted on the pedal cylinder. Pressure created in the pedal cylinder is transmitted to the four wheel cylinders. The pedal cylinder has a diameter of 0.500 cm and each wheel cylinder has a diameter of 2.50 cm. How much pressure is transmitted in the hydraulic system? Express your answer in atmospheres.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A hydraulic motor with a displacement of 2.5 in/rev and a mechanical efficiency of .89 operates at…

Q: Explain the transfer energy and how this affects the behaviour of the system.

A: In thermodynamics a region where the study is performed is known as the thermodynamic system. There…

Q: mechanism like these below, if it is known that O2A length is 5 cm, ab length is 10 centimeters and…

Q: The tune-up specifications of a car call for the spark plugs to be tightened to a torque of 38 N ⋅…

A: Given: The torque applied on the spark plug is T=38 N-m. The length of the wrench is L=25 cm. The…

Q: Suppose the master cylinder in a hydraulic system is at a greater height than the slave cylinder.…

A: Understand that the pressure is defined as the ratio of the force applied to the cross-sectional…

Q: from a pivot point and can rotate around this point. The point is located on the top right corner of…

Q: 6. A force of 85N is applied to a wrench in a clockwise direction at 62° to the handle and 21 cm…

Q: Two masses are fixed at 79 degrees to each other on a rotating disc, one is 3.2 kg at a radius of…

A: This question is based on the concept of balancing.

Q: A rod has 14.0 kg of mass distributed uniformly over its length of 2.50 m and is suspended by two…

A: Given data as per question Mass of the rod =14 kg Length of rod =2.5 m When the rope is cut, the…

Q: Find the magnitude of the net torque on the wheel in Figure below about the axle through O, taking a…

Q: The gearbox shown below is connected at one side to an axis moved by a motor. This motor produces a…

Q: A block of mass 40 kg slides to the right due to the application of the force T. Neglect the mass of…

A: Given:m=40 kgT=100 Nμs=0.5μk=0.4

Q: 80 lb/ft В - 5 ft – 2-5 5 ft A 60 lb/ft 12 ft

Q: A 150 mm diameter pipe bends through 90° in a horizontal plane and while bending changes its…

A: According to the Newton's second law of motion, the rate of change of linear momentum produces…

Q: For a pumper truck pumping water to a fire, the back pressure is the additional pressure on the pump…

A: The total height of the building is h= (16 ft)*9 h= 144 ft

Q: 4. Which of the systems in the following P-V diagram performs the most work? a. System A b. System B…

A: It is known that work is given by area under P-V diagram.

Q: Draw the FBDs for the following system with its distributed loads simplified to their equivalent…

A: UDL load w=800N/m Length of the beam =L=32+42=5m =CB We need to find FBD of the UDL beam FBD of the…

Q: An explosion inside a factory produces a pressure wave of 2lb/in2 against a window. Find the force…

A: The unit of pressure is given in lb/in2. But the unit comes out in m2. Hence convert square meter…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Consider the automobile hydraulic system shown in Figure. Suppose a force of 100 N is applied to the brake pedal, which
acts on the pedal cylinder (acting as a "master" cylinder) through a lever. A force of 500 N is exerted on the pedal cylinder.
Pressure created in the pedal cylinder is transmitted to the four wheel cylinders. The pedal cylinder has a diameter of
0.500 cm and each wheel cylinder has a diameter of 2.50 cm. How much pressure is transmitted in the hydraulic system?
Express your answer in atmospheres.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the given data

VIEW

Step 2: Calculate the pressure transmitted

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hydraulic cylinder is used to lift a load of 750 lbf a distance of 4 ft in 3 seconds. Compute the power and fluid horsepower. OP = 1.8 hp and FHP = 1.82 P= 4.7 hp and FHP = 4.7 P= 6.4 hp and FHP = 7.8 O P= 7.2 hp and FHP = 16.4
2. Some of the first power-generating wind turbines were small, having blades with a radius of 8.00 meters. Currently, the largest wind turbine has a radius of 164 meters. Because the small wind turbines are closer to the ground, they often experience smaller wind speeds. Given the information below, how many small wind turbines would be needed to produce the same power output as one large wind turbine? For both wind turbines, assume the air density is 1.23 kg m³. Small Wind Turbine Large Wind Turbine Wind turbine blade radius 8.00 m 164 m Wind turbine efficiency 35% 45% Wind speed 3.50 m s1 5.50 m s1
can you please find solution for this question
A greedy cat of 4 kg is suspended at the end of the cabinet with a flap in which we store his treats (see the figure on the image). The valve is held in place by a rope attached to 5 cm from the pivot and acts at 10 in relation to the vertical. The damper is a homogeneous wood board of 2 kg mass and has an angle of 20 under the horizontal when opened. What is the tension module in the rope? 2. Determine the module of the horizontal and vertical forces exerted by the pivot.
Find cable AO or BO or OC force vector.
A spring has a natural length 10 in and requires a force of 5 lb to stretch the spring an additional 2 in beyond its natural length. Find the work done in stretching the spring 8 in beyond its natural length.
2. For the system below: a. Give an equation of motion for h. Note that the system has two inputs, p1 and p2. b. When h= 5, give the force exerted on the bottom of the tank. (Assume that the width and height of the opening at the bottom of the tank is negligible. The area of the bottom of the tank is A). h PA PI P2 PA R
Draw the FBDs for the following system with its distributed loads simplified to their equivalentloads.Draw the FBD where the system is the bar. You can find the system in the image with all the details.
3. Please calculate the annual electricity production of a wind farm with 20 turbines. The annual mean wind speed is 7 m/s and diameter of the blades is 20 m. If we assume power consumption of a person is 3,000 kWh, about how many people will this energy support? Annual electricity production (KWh) = K Vm³ At T Where: - - - K = 3.2 (factor based on turbine performance) Vm= annual mean wind speed (m/s) At = swept area of turbine (m2) T = number of turbines Suitable for medium- to large-scale wind turbines (> 200 m2 swept area)
Please find the Thrust bearing reactions in second image as well as tension in cable DE. Thank you.
Draw the FBDs for the following system with its distributed loads simplified to their equivalentloads. Draw the FBD where the system is the bar. You can find the system in the image provided below.
A greedy cat of 4 kg is suspended at the end of the cabinet with a flap in which we store his treats (see the figure on the next page). The valve is held in place by a rope attached to 5 cm from the pivot and acts at 10 in relation to the vertical. The damper is a homogeneous wood board of 2 kg mass and has an angle of 20 under the horizontal when opened. What is the tension module in the rope? 2. Determine the module of the horizontal and vertical forces exerted by the pivot.