Consider the arrangement shown in the figure below. AsSsume that R = 6.00 Q, -1.20 m, and a uniform 2.50T magneticfield is directed into the page. At what speed (in units of m/s) should the bar be mnoved to produce a current of 5.5 A inthe resistor?inRddeSelect one:OA. 22.00OB. 11.00OC. 7.15OD. 3.67OE 13.75Next pageEN* * x * **X X x x x A long solenoid is wound with 960 turns per meter of thin wire through which a current of 17.5 mA is maintained. What isthe magnitude of the magnetic field (in units of uT) at any point inside the coil?Select one:O A. 19.4OB. 14.1OC. 21.1OD. 8.9OE 38.6Next page06:45Y-TU-O

Given:- The resistance R= 6.0 ohm The current I = 5.5 A The length L= 1.2 m The magnetic field B…

Consider the arrangement shown in the figure below. Assume that R = 6.00 Q, 1-1.20 m, and a uniform 2.50T magnetic field is directed into the page. At what speed (in units of m/s) should the bar be moved to produce a current of 5.5 A in the resistor?

Consider the arrangement shown in the figure below. Assume that R = 6.00 Q, 1-1.20 m, and a uniform 2.50T magnetic field is directed into the page. At what speed (in units of m/s) should the bar be moved to produce a current of 5.5 A in the resistor?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A thin 50 cm (0.5 m) long metal bar with mass 0.75 kg rests on (but is not attached to) two metallic supports in a uniform 0.45 T magnetic field as shown in the figure. A battery and a 25 Ω resistor in series are connected to the supports.Find the highest voltage the battery can have wihtout breaking the circuit and the initial acceleration of the bar if the resistor decreased resistance to 2 ohms.
In the figure, an electron with an initial kinetic energy of 3.80 keV enters region 1 at time t = 0. That region contains a uniform magnetic field directed into the page, with magnitude 0.0100 T. The electron goes through a half-circle and then exits region 1, headed toward region 2 across a gap of 30.0 cm. There is an electric potential difference AV = 2000 V across the gap, with a polarity such that the electron's speed increases uniformly as it traverses the gap. Region 2 contains a uniform magnetic field directed out of the page, with magnitude 0.0168 T. The electron goes through a half-circle and then leaves region 2. At what time t does it leave? Number i Units × B₁ Region 1 Region 2 OB₂
A straight conductor of length L moves with an acceleration A =0.1 ms-2 at right angles to a magnetic field of uniform strength B=10.2 T. Calculate L, considering that the e.m.f., ? = BLv, between the ends of the conductor increased from 0 to 5 V during the first 20 s after the beginning of motion.
A square wire loop with 1.7 m sides is perpendicular to a uniform magnetic field, with half the area of the loop in the field as shown in the figure. The loop contains an ideal battery with emf = 17 V. If the magnitude of the field varies with time according to B = 0.035 T - (0.90 T/s)t, with B in teslas and t in seconds, what are (a) the net emf in the circuit and (b) the direction of the (net) current around the loop? 29. ● B E ba bat
Two lined conductors are connected by a resistor R=30Ω, and separated by L=5. A moving conductor of mass m slides on the conductors at a constant speed v, which produces a current I=4 A. The conductors are placed in a B=6T magnetic field out of the page. In what direction does the current flow through the moving conductor when the bar is sliding in the direction as shown in the figure? From the previous question, calculate the speed at which the bar is moving. From the previous question, calculate the magnitude and direction of magnetic force on the bar.
In the figure (Figure 1) a conducting rod of length L = 40.0 cm moves in a magnetic field B of magnitude 0.410 T directed into the plane of the figure. The rod moves with speed v = 5.60 m/s in the direction shown. Part F What is the potential difference across the rod if it moves parallel to ab? Express your answer in volts. Figure < 1 of 1 ? V = 0.91 V B х ах
A square coil of wire of side 3.90 cm is placed in a uniform magnetic field of magnitude 2.50 T directed into the page as in the figure shown below. The coil has 39.0 turns and a resistance of 0.780 Ω. If the coil is rotated through an angle of 90.0° about the horizontal axis shown in 0.335 s, find the following. A square coil is shown in the plane of the page, and inside the coil a magnetic field points into the page. A horizontal rotation axis passes through the middle of the square. An arrow indicates that the square rotates clockwise on the axis when viewed from the left. (a) the magnitude of the average emf induced in the coil during this rotation mV(b) the average current induced in the coil during this rotation mA
An electrically conductive rod is moving through a uniform magnetic flux at a constant velocity at right angles, as shown by its cross-section in the diagram. The velocity is in the x-direction, the rod is of length 150 mm along z, and the magnetic flux density is 0.2 T in the positive y-direction. Speed If the potential difference (voltage) across the ends of the rod is 5.8 Volts, what is the magnitude of the velocity? m/s Not perpendicular If the rod is passing through the flux with its axis not at right angles what can you be sure of? The speed to generate 5.8 V would have to be smaller. • The speed to generate 5.8 V would have to be bigger. The speed to generate 5.8 V would be the same.
The coil in the picture below is rotating with a constant angular speed of 320 rad/s in a uniform magnetic field of 0.200 T. The diameter of the coil is 10 cm. Calculate the magnitude (ie., a positive value) of the maximum value of the induced current, in mA, if the resistance of the coil is 20 Q. B.
The slide generator in the figure below is in a uniform magnetic field of magnitude 0.0500 T. The bar of length 0.390 m is pulled at a constant speed of 0.500 m/s. The U-shaped conductor and the bar have a resistivity of 2.75 x 10-80 m and a cross-sectional area of 9.50 x 10-4 m². Find the current in the generator when x = 0.680 m. (Note that the A in the image below is the area of the loop, not the cross-sectional area of the conductor and bar.) A Bulb is unlit. A. B. Bulb is lit. O O O O( O O a G O O O O ܥܘ O O O O OG O O O O O O B BO Ā OOO O B₁ I loop O 0 0 O X F O • O O O O mech O O Activate Windows Go to Settings to activate Windows.
The conducting loop of the shape shown in the figure is being pulled out of a constantBext magnetic field at a constant speed v. The left part of the loop KN is a semicircle ofradius a. The top and the bottom parts of the loop are equal, KL=NM=b. Theresistance per unit length of the conductor is r (Ω/m). During the time intervalbetween when line LM and then KN are at the border of the magnetic field,a) What is the direction ofthe induced current? Explainyour choice of direction.b) What is the EMFproduced in the loop?c) What is the size of theinduced current?
The figure below shows a top view of a bar that can slide on two frictionless rails. The resistor is R = 5.60 0, and a 2.50-T magnetic field is directed perpendicularly downward, into the page. Let { = 1.20 m. Bin R app (a) Calculate the applied force required to move the bar to the right at a constant speed of 2.30 m/s. N (to the right) (b) At what rate is energy delivered to the resistor? W