Consider the area shown in (Figure 1). Suppose that a = 2.4 in., b = 4.8 in., c = 1.6 in.

Q: Height is 20 in. not 10 in.  Find The moment of inertia of the combined section with respect to…

A: Consider the figure: yc=∑Ay¯∑A…

Q: 2. The bracket BCD is hinged at C and attached to a control cable at B. For the loading shown in…

A: To find : determine the tension in the cable and the reaction at C.

Q: 10 MPa 40 MPa 50 MPa

A: Given, σx = 50 MPa σy = -10 MPa τxy = 40 MPa   Radius of mohr circle is given by, R = σx - σy22 +…

Q: Q/1-B: For the solid geometry shown in figure below, construct the required CSG tree.

A: Find Construct the required CGS tree.

Q: Find the centroid of the shaded portion as shown in figure. Where b1 =85 mm, d %3D

A:

Q: b) Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

A:

Q: The diagram shows the dimensions of a garden shed and a long pole that just fits into the shed…

A:

Q: Q3:the shaded area shown in the figure find Moment of Inertia With respect to the X-axis. Azam 9cm…

A: When an amount of force act at the end of the object, it has the tendency to rotate the object about…

Q: g x direction. The initial strain along y direction. The initial strain in z direction Additional…

A: Rectangular steel block  Lx = 3 inchLy = 2 inchLz = 4 inch Fx = + 30 kipsFy = -60 kipsFz = 54 kips

Q: Mohr's circle for an element is shown below, each grid square is 20 MPa. The principal plane is: I…

A:

Q: s lowest point to the ground. Choices: 150m ,153m , 148m , 145

A: length = 300m   weight = 600kf   tension = 4ookg , 450kg

Q: 3. How to locate a short cylindrical component? Please use a drawing for the illustration and point…

A: To find: How to locate a short cylindrical component.

Q: 2 m 1 m For the figure below, the center of :gravity is y₁ 2 m 3 m X'= 2.65 AND Y'= 1.217 O X'=1.217…

A:

Q: 3. A mobile is constructed of light rods, light strings, and beach souvenirs as shown in the figure…

A: As per our Q&A guidelines we are supposed to solve only one question at once and also only first…

Q: 2 m 1 m For the figure below, the center of :gravity is 2 m 3 m X'= 2.65 AND Y'= 1.217 O X'=1.217…

A:

Q: Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

A:

Q: For the planar area symmetrical with respect to the x-axis in the figure, the cross-section…

A: Consider the section as shown below, Area ABCD, A1=24a+ca+2aA1=24×1+31+2×1A1=42 cm2Centroid of…

Q: A trench is constructed from 5 steel plates. Each plate is 1m X 1m. Plates A,B, and C are horizontal…

A: To Find : The moment about the axis from point G to H. Given:  The dimension of plate is A=1m·1m.…

Q: Find the - 2i - 1oj - I Ax B

A: Given: →A= 2i-10j-11k→B = 2i+2j+k Let θ be the angle between →A and →B Then  θ= cos-1 →A . →B→A →B…

Q: 100 Mpa 75 Mpa 150 Mpa If the element shown was rotated 60° CW Find: (α)σχ' (b)ay' (c)tx'y'

A:

Q: Q5: Determine the horizontal and vertical components of force needed to hold the Y, shown in figure…

A:

Q: Mohr's circle for an element is shown below, each grid square is 20 MPa. The principal plane is: 1…

A:

Q: Consider the figure below. If T1=3,500 lbs and T2 = 2,500lbs, fin the angle alpha made by T2 from…

A: Given data: Tension T1=3500 lbs Tension T2=2500 lbs

Q: 100 Mpa 75 Mpa 150 Mpa If the element shown was rotated 60° CW Find: (α)σχ' (b)oy' (c)tx'y'

A:

Q: Question #3: There is a linearly distributed load applied around a circle (below). The magnitude of…

A: Given-Information: Magnitude,λ=14lb/ftRadius, R=3ft To-Determine: 1. Moment at A, B. 2. Net force.…

Q: A square plate with sides 1.5 m in length can rotate around an axle passing through its center of…

A: Given Data Force acting at top left edge is: F1=30 N Force acting at the bottom left edge is: F2=20…

Q: Given the figure below. Find the momemt of F about O. 4 ft F, = {100i – 120j + 75k} lb 5 ft. 3 ft

A:

Q: A 3.00 m long, 8.0 kg pole is attached to a wall by a hinge on its left side. A cable attached to…

A: To find: (a) To write the sum of forces and sum of torque equations. (b) The tension in the cable.…

Q: Q3:the shaded area shown in the figure find Moment of Inertía With respect to the Xasis 2cm 10 cm-

A:

Q: Determine the center of mass for the laminae given in figure.

A:

Q: For the composite object below (figure not to scale), the top triangle is made of titanium (density…

A: It is asked to find the centroid and moment of inertia based on the image shown below

Q: Find the centroid of the region shown in Figure

A: Divide the given area into three sections as shown in the below diagram.

Q: FIND THE FOLLOWING SHAPE WEIGHT CENTER BY REFERENCES O point.

A: Write the expression of distance c.

Q: b) Write the centroid formula for this problem. c) Apply the above formula to find the y- component…

A:

Q: Q2. As shown in the image below, the rigid member ABC is subjected to three forces. The forces are…

A:

Q: 14. Form the Fig.(2) The second moment of area Iyy is then given by; 50mm Imm 120mm 2mm Fig. (2) 2mm…

A: Find the moment of inertia of the section of the non circle

Q: Three force F, F, and F, acting on a support as shown in Figure 2. 1' 2 i. Compute the components in…

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.