Consider continuous two-dimensional heat transfer in a rectangular cross- section solid rod as given in the figure. The measured temperatures at selected nodes of the outer surfaces are shown in the figure. The thermal conductivity of the object is given in two different ways as follows and there is no heat generation inside the object. The rectangular shape is divided into 6 equal parts as and. Find the temperatures of the determined points in the environment using the finite difference method. (1, 2, 3 and 4 points) AX = AY = 2cm ve k=20 W/m°C 120 120 100 100 120 120 [3 140 140 insulation 2.

Consider continuous two-dimensional heat transfer in a rectangular cross- section solid rod as given in the figure. The measured temperatures at selected nodes of the outer surfaces are shown in the figure. The thermal conductivity of the object is given in two different ways as follows and there is no heat generation inside the object. The rectangular shape is divided into 6 equal parts as and. Find the temperatures of the determined points in the environment using the finite difference method. (1, 2, 3 and 4 points) AX = AY = 2cm ve k=20 W/m°C 120 120 100 100 120 120 [3 140 140 insulation 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
Consider the composite wall system formed by a flat plate of solid material I attached in series to a flat plate of solid material II as shown in IMAGE BELOW The straight lines observed in each material correspond to the temperature profiles in steady state.According to the above, you are asked: Which of the two materials has the highest thermal conductivity?
Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
A long solid bar (k=30 W/m.K) of rectangular cross section is exposed to a constant heat flux on one surface and is subjected to convection on the opposite surface. The other two surfaces are maintained at constant temperatures as shown. Using a uniform mesh size Ax=Ay=1 cm, 6.1 express the finite difference equations for nodes 1, 2 and 3, and 6.2 solve for the nodal temperatures. 100 °C q=5,000 W/m² 300 °C ΔΧ 3 ду h = 150 W/m²K Too = 25 °C
5-23 Consider steady one-dimensional heat conduction in a pin fin of constant diameter D with constant thermal conductivity. The fin is losing heat by convection to the ambient air at Too with a convection coefficient of h, and by radiation to the surrounding surfaces at an average temperature of Turr The nodal network of the fin consists of nodes 0 (at the base), 1 (in the middle), and 2 (at the fin tip) with a uniform nodal spacing of Ax. Using the energy balance approach, obtain the finite difference formulation of this problem to determine Tand T for the case of specified temperature at the fin base and negligible heat transfer at the fin tip. All temperatures are in °C FIGURE P5-23 Turr To Radiation e h, To Convection
The lining of box-type fumace is made up of a refractory layer and steel plate as shown in the figure. Steady state temperature at the surface of the refractory is 1273 K and that at the outer steel surface is 473 K. If the steady state heat flux through the refractory-steel plate composite is 1600 W/m², and heat flow is along x-direction only, the thermal contact resistance (m² K/W) between refractory and steel is_ steel Refractory 1273K Furnace 473K Ambient Given data: Thermal conductivity of refractory = 1.2 W/m-K Thickness of refractory lining = 80mm Thermal conductivity of steel = 32 W/mK Thickness of steel plate = 4mm
Two approaches used in development of the thermal resistance network in the x-direction for multi-dimensional problems are to assume any plane wall normal to the x-axis to be isothermal and to assume any plane parallel to the x-axis to be adiabatic. True or False True False