Consider an LTI system for which the system function H(s) has the following pole-zero pattern. (a) Indicate all possible ROCs that can be associated with this pole-zero pattern. (b) For each ROC identified in part (a), specify whether the associated system is stable and/or causal. Im Re * X X -2 -1 2 -X

Consider an LTI system for which the system function H(s) has the following pole-zero pattern. (a) Indicate all possible ROCs that can be associated with this pole-zero pattern. (b) For each ROC identified in part (a), specify whether the associated system is stable and/or causal. Im Re * X X -2 -1 2 -X

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 24RQ

See similar textbooks

Similar questions

In a communication system the signal sent from point a to point b arrives by two paths in parallel. For path 1, the signal passes through two repeaters ( in series ). Each repeater has probability of failing ( becoming an open circuit ) of 0.1. For path 2, the signal passes through one repeater with a probability of failing of 0.08. All repeaters fail independently of each other. Find the probability that the signal will not arrive at point b. O 0.0152 O 0.016 0.008 0.09
(a) Explain the main different between a 2-bit asynchronous counter and a frequency divider by 4 with the aid of appropriate diagram. (b) Determine the sequence of the counter shown in Figure 7 and explain the function of NAND gate in the circuit. Begin with the condition that the counter is cleared. Show the appropriate waveforms for all input and outputs to support your answer using the answer sheet provided in Appendix. Do D D2 CLK Figure 7 |Rajah 7) (c) Design a synchronous counter that can count up and down for a sequence of 3+2+»5+>1 using D flip-flops.
VI. FILL-IN QUESTIONS: 1. Before the TRIAC is triggered on, the voltage across its main terminals is equal to the voltage. 2. When the TRIAC is triggered on, the voltage across its main terminal is about V. 3. Once the TRIAC is conducting, the gate_control the current to flow through the TRIAC. 4. The TRIAC can be turned off by reducing the current through it below its The TRIAC can have_or__terminal voltage and be triggered on by_applied on the gate.
To implement 8-to-1 line multiplexer using two 4-to-1 line multiplexer(MUX): O a. The third selctor is connected to the enable line of the first and second MUX. O b. Only the enable line of the first MUX must be connected dirictly to the enable for the second MUX. O c. The third selctor is connected to the enable line of the first MUX which is connected through inverter to the enable of the second MUX. O d. All inputs lines for the first mux must be connected to the input lines for the second mux.
De fine time constant (I) for (R-L) cct.
Identify THREE characteristics of TTL.
ANSWER 4 AND 5 ONLY
Consider the line of code below. analogWrite(11, 84); The voltage at pin 11 is turns on (at 5V for Uno) and off at 500 Hz. This PWM frequency is the default value for Arduino boards. How many microseconds is the voltage at pin 11 high?
When the pinch-off voltage is exceeded, ID will ____ as VDD increases. remains the same double increases decreases
With a block-diagram, write about “TIE-LINE BIAS CONTROL
1. Convert: 0.FF16 = _____________ 10 2. Convert from Binary to Gray code: 11010100102 = _______________________ Gray code 3. BCD Addition: 7892 + 797 = 4. Signed Binary Operation: -85310 - 39810 I need answer ASAP. Thank you so muccch!!
When making an ECG measurement, it is important to measure voltage variations over small time intervals. The time is limited by the RC constant of the circuit—it is not possible to measure time variations shorter than RC. How would you manipulate and in the circuit to allow the necessary easurements?