Consider an infinitely long electrically conducting cylinder of radius 5 m and along the z direction as shown in Fig. Q3. This cylinder is fabricated with one inner cylindrical hole of a radius of a 2. Assume that the current I of 10 A flowing in the z-direction is uniformly distributed in the conducting cylinder. Q.3 Calculate the magnetic field for (p= r +y >a) anywhere outside of the conducting cylinder. (Hint: Use (x, y) variables to express your solutions to the x- and y-components of the magnetic field.) (a) (Ъ) Calculate the magnetic field for (p= x² +y

Consider an infinitely long electrically conducting cylinder of radius 5 m and along the z direction as shown in Fig. Q3. This cylinder is fabricated with one inner cylindrical hole of a radius of a 2. Assume that the current I of 10 A flowing in the z-direction is uniformly distributed in the conducting cylinder. Q.3 Calculate the magnetic field for (p= r +y >a) anywhere outside of the conducting cylinder. (Hint: Use (x, y) variables to express your solutions to the x- and y-components of the magnetic field.) (a) (Ъ) Calculate the magnetic field for (p= x² +y

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write the equations to determine the value of the magnetic field in the air gap in this circuit. Assume that the core of a permeability µ has a uniform cross section A. The values of I, N, I1, l2, I3, and l4 are given. 13 Air gap 13
please solve accurate, this is my important homework.
Please write legibly.
A wire of length 50 cm and mass 10 gr. is suspended in a horizontal plane by a pair of flexible leads as seen in the figure below. The wire is then subjected to a constant magnetic field of magnitude 0,5 T, which is directed as shown. What are the magnitude and direction of the current in the wire needed to remove the tension in the supporting leads? Fm 50 cm mg (a) (b)
A 15.0-cm horizontal wire of mass 15 g is placed between two thin, vertical conductors, in a region where a uniform magnetic field exist as shown. The magnetic field density required to just left the wire up is A) 0.196 T out of page B) 0.196 T into the page C) 0.226 T out of page D) 0.226 T into the page E) none of these
Choose the correct answer. *Please answer it ASAP if you can
Please do problem 1
Consider the following current density with and a = 1mm and b = 16mm; %3D J= 4 a, mAlm? if a b .
square coil with current, mr rib a = 2cm is located in the homogeneous magnetic field with induction 0.2 tesla and its perpendicular forms the angle 60 °, with the lines of induction. Knowing that the moment of magnetic forces is 2 × 10-³ N × m to be determined: a) The magnetic moment of the coil and the current in the coil
1. In the magnetic system (Fig. 1), the width of the vertical limbs of the core a=16mm, the width of the horizontal limbs b=13mm, the distance between the limbs d362mm, and the depth of the core is 17mm. The left coil has 170 turns and the right one has 71 turns. The - B-H curve of the core material can be d. Ni d N2 approximated as: B=(H/1015)0.37 (T), if H is less than or equal to 470At/m, and B=1.05726(H/970)0.47 (T), if H is greater than 470At/m. The unit of H is At/m. b (a) If I1=0.57A, determine the value of I2 to produce a flux density in the vertical limbs of the core as Ba-0.74T; (b) If I=0.51A and I2=0.88A, determine the flux density in the vertical limbs Ba, and the one in the horizontal limbs Bb. Fig. 1
Kindly share detailed explanation for each step and each options.
A uniformly charged, straight filament 8 m in length has a total positive charge of 4 HC. An uncharged candboard cylinder 4 cm in length and 12 cm in radius sUCTOunds the filament at its center, with the filament as the axis of the cylinder. Using reasonable approximations, find (a)the electric field at the surface of the cylinder and (b) the total electric flux through the cylinder.