Consider an aluminum pan used to cook food on top of an electric range. The bottom section of the pan has thickness of L = 0.3 cm and diameter of D = 20 cm. The electric heating unit transfers 800 W of power to the pan. During steady operation, the temperature of the inner surface of the pan is measured to be 110°C. Which of the following boundary conditions is correct during this cooking process; Water

Consider an aluminum pan used to cook food on top of an electric range. The bottom section of the pan has thickness of L = 0.3 cm and diameter of D = 20 cm. The electric heating unit transfers 800 W of power to the pan. During steady operation, the temperature of the inner surface of the pan is measured to be 110°C. Which of the following boundary conditions is correct during this cooking process; Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a certain experiment, cylindrical samples of diameter 4 cm and length 7 cm are used, as shown in Figure 5 below. The two thermocouples in each sample are placed 3 cm apart. After initial transients, the electric heater is observed to draw 0.6 A at 110 V, and both differential thermometers read a temperature difference of 8°C. Determine the thermal conductivity of the sample. Cooling fluid Thermo couple Sample L = 3 cml }AT; 7 cm 4 сm a a Resistance heater L= 3 cm[ }AT, Sample Insulation -Cooling fluid Figure 5
If you have a room (10*7*3.5m) and you have 2 solar windows (the dimension of the window (2.5*2m)) located in the largest wall and the solar gain of them 1.5 kW/day and you have a door (1.6*2.5 m) in the northern wall and the temperature inside = 21°c and the average temperature outside = 10°C and the natural air change = 0.9 time /hour/day and the characteristics of materials are shown in the table below Elements U value Window 1.4 W/m.K Door 2.5 W/m.K South and North wall 0.5 W/m .K East and west wall 0.65 W/m .K Roof 0.45 W/m.K Floor 0.7 W/m .K If you know that you have 6 fixture lighting units of 50 W and the efficiency of them 70% and their runtime is 10 hours /day and there are 3 persons one of them is cooking and the two other are sleeping and they are present 4 hours/day and if you have the following appliance Appliance Running time Rotisserie 0.2 hour Large refrigerator 5 hours Blender 0.2 hour From your heat balance result decide if we will need a cooling or a heating system…
The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k = 240 W/m.K) or copper (k = 390 W/m-K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C and heat is transferred from the stove to the pan at a rate of 1200 W. What is the temperature of the surface in contact with the stove for each of the two materials? Aluminum: T = i °℃ Copper: T = °℃ i
Thin walled Aluminum container that is 6 cm in diameter and 7 cm in high equipped with stirrer contain water submersed in hot engine oil at 60°C. If the oil was mixed by the stirrer and the heat transfer coefficient between the water and the glass is 120 W/m2. °C. Find the time needed for the water to heat up from 3°C to 38°C
A brass wire of 0.8 mm in diameter and 12 m long is annealed in an annealing furnace at a temperature of 400°C. Find the time required for the wire to reach the temperature of 150°C if the temperature of the wire before placing it inside the furnace is 30°C. Take h = 35 W/m2 K. Density = 8500 kg/m3. Specific heat = 0.335 kJ/kg K.
40°C water with hwater = 800 W/m² K is flowing in a Pyrex tube. The inner and outer diameters of the tube are 25 mm and 35 mm. A thin metallic heater element bonded to the outer surface of the tube is being used to heat the water by transferring 600 W/m of thermal energy to the water flowing in the tube. The Pyrex tube and heater are covered with a 10-mm thick layer of foam insulation. The outer surface of the foam insulation is exposed to air at T = -5°C with hair = 12 W/m².K. The heater = air element must generate more than 600 W/m, because part of the heat being generated is lost to the air surrounding the foam insulation. Assume kp = 1.30 W/m K for Pyrex and k = 0.026 W/m K for the foam insulation. a) Find the temperature of the heater element needed to transfer 600 W/m of thermal energy to the water in the tube. b) Find the total rate at which the heater element must generate thermal energy. Water Pyrex tube, kp = 1.30 W/m.K = 40°C water hwater = 800 W/m².K Heater element Tair=…
A piece of chromium steel of length 7.4 cm (density = 8780 kg/m^3; k = 50 w/mK and specific heat cp = 440j/kgK with mass 1.27 kg is rolled into a solid cylinder and heated to a temperature of 600 deg C and quenched in oil at 36 deg C. Show that the lumped capacitance system analysis is applicable and find the temperature of the cylinder after 4 min. What is the total heat transfer during the period? You may take the convective heat transfer coefficient between the oil and cylinder at 280 w/m^2 k.
A carton (50 cm x 30 cm x 85 cm) of milk, initially at 23°C, was placed in a refrigerator with the thermostat set to 4°C. After 3 hours, the temperature of the milk dropped by 3.6°C. Using the lumped systems analysis, estimate the heat transfer coefficient for the cooling of milk in the refrigerator given the following properties of milk: Density: 1035 kg/m³ Specific heat capacity: 3930 J/kg.K Thermal conductivity: 0.278 W/m·K Explain why the lumped system analysis is applicable in this situation.
A glass window with an area of 0.625 m² is installed in the wooden outside wall of a room. The wall dimensions are 25 x 3.05 m. The wood has a k of 0.151W/m.K and is 3.05 cm thick. The glass has a k of 0.692W/m.K and is 5.0 mm thick. The temperature of the inside room is 27°C and outside air temperature is 268K. (1)What is the heat loss through wooden wall and glass window q(W) ? (2) What are the total heat loss?
16-90 An electric heater with the total surface area of 0.25 m² and emissivity 0.75 is in a room where the air has a temperature of 20°C and the walls are at 10°C. When the heater consumes 500 W of electric power, its surface has a steady temperature of 120°C. Determine the temperature of the heater surface when it consumes 700 W. Solve the problem (a) assuming negligible radiation and (b) taking radiation into consideration. Based on your results, comment on the assumption made in part (a). We Too, h FIGURE P16-90 Ts Α, ε Qconv Qrad Tw
Two metal rods of equal length-one aluminum, the other stainless steel-are connected in parallel with a temperature of 18.0 ∘C at one end and 110 ∘C at the other end. Both rods have a circular cross section with a diameter of 6.00 cm Determine the length the rods must have if the combined rate of heat flow through them is to be 17.5 JJ per second. If the length of the rods is doubled, by what factor does the rate of heat flow change?
You want to heat a house on a very cold day as shown in the figure. To do this, you want to use photovoltaic panels as an energy source. It would be about using 15 panels each with an area of 1.5 m2. These panels would be connected to an electrical resistance that would heat the house as shown in the figure. The house is losing heat through the walls and ceiling as shown in the figure. The panels are receiving solar radiation at a rate of 800 W / m2 and if their efficiency is 15%. How much will the temperature of the house rise after an hour? The house is hermetically sealed. Assume that the specific heats of air, cv and cp, are constant as shown in the figure. sol = sun fuga = leakage aire = air