Consider a rectangular fin that is used to cool a motorcycle engine. The fin is 0.15 m long and at a temperature of 250°C, while the motorcycle is moving at 60 km/h in air at 27°C. The air is in parallel flow over both surfaces of the fin, and turbulent flow conditions may be assumed to exist throughout. What is the rate of heat removal per unit width of the fin, in W/m? eTextbook and Media Save for Later W/m

Consider a rectangular fin that is used to cool a motorcycle engine. The fin is 0.15 m long and at a temperature of 250°C, while the motorcycle is moving at 60 km/h in air at 27°C. The air is in parallel flow over both surfaces of the fin, and turbulent flow conditions may be assumed to exist throughout. What is the rate of heat removal per unit width of the fin, in W/m? eTextbook and Media Save for Later W/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the ratio of thermal-boundary-layer thickness to hydrodynamic-boundary- layer thickness for the following fluids: air at 1 atm and 20°C, water at 20°C, helium at 1 atm and 20°C, liquid ammonia at 20°C, glycerine at 20°C.
Calculate the convective heat transfer rate via the top and the two side walls of a refrigerated box trailer as shown in the figure. The trailer is cruising at a rate of 70 mph (31.3 m/s). The box trailer dimensions are 16 m long, 4.1 m high, and 2.6 m wide. Assume that the surface of the trailer is at uniform temperature of 10°C. The air temperature is 30°C. Because of the presence of the prime-mover in the front, the air flow can be assumed to be turbulent when it encounters the trailer. 187.4 kW Walls. Prime-mover 16 m 2.6 m
Air at 20°C flows over a plate which is at 80°C and temperature at a location of 0.5mm from surface is measured to be 50°C. Assuming themal conductivity of fluid as 0.025W/mK, the local convective heat transfer coefficient will be (A) 25W/ m²K (B) 30W / m²K (C) 35W/ m²K (D) 40 W / m²K
Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? I need the solution from fundamental concepts of how the heat flow behaves in the system
Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with velocity of 1 m/s: atmospheric air, water, engine oil, and mercury. For each fluid, determine the velocity and thermal boundary layer thicknesses, in mm, at a distance of 25 mm from the leading edge. Fluid Air Water Engine Oil i Mercury 8 (mm) i i 8, (mm)
i need the answer quickly
A vertical pipe 90 mm diameter and 2.5 m height is maintained at a constant temperature of 125 o The pipe is surrounded by still atmospheric air at 25 oC. Find heat loss by natural convection. Properties of water at 75 oC: Density = 1.0145 kg/m3 Kinematic viscosity = 20.55 x10-6 m2/s Prandtl number (Pr) = 0.693 Thermal conductivity (k) = 30.06 x 10–3 W/m K
Engine oil at 100°C and a velocity of 0.20 m/s flows over both surfaces of a 1.1-m-long flat plate maintained at 20°C. Determine: (a) The velocity and thermal boundary layer thicknesses at the trailing edge. (b) The local heat flux and surface shear stress at the trailing edge. (c) The total drag force and heat transfer per unit width of the plate. Determine the velocity boundary layer thickness & at the trailing edge, in m. 8 = i m Determine the thermal boundary layer thicknesses &, at the trailing edge, in m. 8, = i m Determine the magnitude of the local heat flux at the trailing edge, W/m². q" x = i W/m² Determine the local surface shear stress at the trailing edge, in N/m². Ts, L i N/m² Determine the total drag force per unit width of the plate, in N/m. D' = i N/m Determine the magnitude of the heat transfer per unit width of the plate, in W/m. d' = W/m i
Heat transfer
In the arctic sea, the ice sheets are melting. Let's calculate the temperautre distribution in one such ice sheet. The sheet is 2 m thick. Under the sheet there is ice-water mixture and it can be assumed that the temperature of the bottom surface of the ice sheet is approximately 0°C. Air at -20°C is blowing above the sheet. The convection coefficient of air is 15 W/m².K. The thermal conductivity of ice is 2.2 W/m.K. What is the temperautre of icesheet at its center (i.e., at 1 m from the surface)?
heat and mass transfer An uninsulated steam pipe of 100-mm diameter is routed through a building whose walls and air are at 27°C. Pressurized steam maintains a pipe surface temperature of 147°C, and the coefficient associated with natural convection is h =10 W/m2.K. The surface emissivity is ɛ= 0.8. What is the rate of heat loss per unit length from the steam line?
A long aluminum wire of diameter 4 mm at a temperature of 370°C is subjected to cross air flow at 30°C at a velocity of 5.8 m/s. What is the conveçtive heat transfer coefficient (W/m".K)? Air properties: v =3.455×10¨ m /s, Pr = 0.6974, k = 0.03779 W/m.°C -5 Select one: