Consider a reciprocating air compressor with two-stage, 6.8 m/min free air delivery at atmospheric conditions of 107 kPa and 19 °C, respectively. The polytropic compression index is 1.21, while the delivery pressure is 2,294 kPa. The mechanical and motor- drive efficiencies are 85% and 93%, respectively. Accept complete inter-cooling and neglect clearance volumes. What is the delivery air temperature in C to no decimal place?

Consider a reciprocating air compressor with two-stage, 6.8 m/min free air delivery at atmospheric conditions of 107 kPa and 19 °C, respectively. The polytropic compression index is 1.21, while the delivery pressure is 2,294 kPa. The mechanical and motor- drive efficiencies are 85% and 93%, respectively. Accept complete inter-cooling and neglect clearance volumes. What is the delivery air temperature in C to no decimal place?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ In one of applications, wanted to condition laboratory at inside design condition DBT=24 °C and 50% Rh and outside design condition DBT=44 °C and WBT=27 °C. Total sensible load for the space is 35 kW and total latent load for the space is 19 kW. Rate of supplied air to the space is 11050 m /hr and rate of outside ventilation air is 4250 m/hr. The recirculated air is mixing with the outside air and then entering to cooling coil and leaving at 95% Rh then the air is passing through heating coil before supply to the space. Determine: 1.Condition of supply air to the conditioned space (DBT & RH); 2.Condition of air before and after cooling coil (DBT & RH); 3. Sensible load of heating coil; 4.Sensible load and latent load and total load of cooling coil; 5. Apparatus dew point (ADP) for the cooling coil; 6. Draw the cycle on the psychrometric chart.
A single reciprocation compressor takes 1m³ of air per minute and 1.013 bar and 15 degree Celsius and delivers at 7 bar. Assuming Adiabatic law(n=1.35) and no clearance. This same compressor is now driven at 300 rpm, has a stroke bore ration of (1.5:1), it has a mechanical efficiency for the compressor of 85% and motor transmission efficiency of 90%. Calculate: Volume per cycle Cylinder bore diameter Power to the compressor Motor power needed The isothermal power The isothermal efficiency
B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine the following data were recorded: Bore 10.5cm; stroke 12.5cm; engine speed 1200 rpm, torque 150 N.m, fuel consumption 5.5 kg/hr, calorific value of fuel, 43124 kJ/kg, ambient temperature 1-The brake thermal efficiency. and pressure are 20°C and 1.03 barş. Calculate: 2-The brakes mean effective pressure. 3-The volumetric efficiency.
A single stage single acting air compressor with runs at speed 600 rpm. It has a polytropic index of 1,26. The induced volume flow rate is 0,72 cubic meters per min and the air must be delivered at a pressure of 707 KPa. The free air conditions are 101,3 KPa and 15 degrees Celsius. The clearance volume is 7,6 % of the stroke volume and the stroke /bore ratio is 1,6/1. Calculate 1.The stroke volume of the cylinder in cubic meters to 5 decimal places. 2.The bore of the piston in meter to 4 decimal places.
I need answer typing clear urjent
b) A single-acting, two-stage reciprocating air compressor runs at a speed of 500 rev/min with overall pressure ratio of 20 to 1 has free air delivery of 5.0 m3/min. For the first stage compressor, the pressure and temperature at the end of induction stroke is 100kPa and 27°C, respectively. The intermediate pressure is 500 kPa, and the intercooling process is complete. The clearance volumes of both stages are 5% of their respective swept volumes. The ambient pressure and temperature are at 100 kPa and 27°C, respectively. The index of compression and expansion, n is 1.3. i) Sketch the cycle on a P-V diagram. ii) Determine final delivery temperature of the compressor, C. iii) Determine totalindicated power, kw. iv) Determine volumetric efficiency for the first stage, %. v) Calculate the swept volume of the first and second stage, m2. Take the value of R for air is 0.287 kl/kg.K.
As shown in the figure, air with a volumetric flow rate of 17,000 ft3/min enters an air-handling unit at 80oF, 1 atm. The air-handling unit delivers air at 45oF, 1 atm to a duct system with three branches consisting of two 26-in.-diameter ducts and one 50-in. duct. The velocity in each 26-in. duct is 19 ft/s. Assume steady state operation and ideal gas behavior for the air. Determine the mass flow rate of air entering the air-handling unit, in lb/s. The volumetric flow rate in each 26-in. duct, in ft3/min. The velocity in the 50-in. duct, in ft/s.
A counter flow air pre-hea ter receives 330,000 lbs/hrs of flow gas at 509°F, for which Cp = 0.234 Btu/(lbs °R), k=1.4 , kb = 0.266 (Btu-i 1)/(ft2-hr-ºR) and R=56 The exit temperature of the gas is 280°F. The gas flows through 3 inches outside dia meter tubes (2.782 inches inside diameter) with an average velocity of 15 fps at atmospheric pressure of 14. psia. What is the film coefficient in the inside of the tube.
5.16.| For a centrifugal compressor rotating at 2500 rpm, find the compression ratio for the following specifications. T = 300 K; nst (volumetric flow rate) = 1.25 m/s and t (the thickness of the flow section at the = 0.85; r, = 0.55; ra = 0.015; B, 60°, exit) =0.15 m.
In a 4-cylinder 4-stroke KA engine with volumetric efficiency nv = 0.85, compression ratio 14: suction reference pressure 96 kPa, suction reference temperature 298 K; Exhaust pressure 108 kPa, exhaust temperature 1200 K; Find the pressure loss in the suction system since the end suction temperature is 310 K. The gas constant of the residual gas is Rr = 291.9 J / kg K, Rref = Rem = 287.13 J / kg K, the stroke volume of the engine is 0.598 liters.
A Gould Brand, German made Single Reciprocating Compressor has a speed of 1200 rpm. The diameter of the cylinder bore is equal to 120mm and a displacement length of stroke equal to 150mm, at suction pressure of 120KPa with 20 degree centigrade to 215 degree centigrade temperatures. Calculate the following: a. Mass Flow rate, kg/sec b. Pressure Ratio c. Indicated Power d. Shaft Power if Mech'l Eff.=80%
QU reciprocating compressor with single acting single stage . the air entering at 15°C and 2 bar . the polytropic compression accur with index 1.3 to pressure 13 bar . speed of compressor 200 tpm and I/d ratio is 1.5 . the mechanical efficiency is 0.7, determine the cylinder dimension , the work required during the process of compression and isothermal efficiency