Consider a pipe that branches out into two parallel pipes and then rejoins at a junction downstream. The two parallel pipes have the same lengths and friction factors. The diameters of the pipes are 2.5 cm and 5 cm. If the flow rate in the 2.5 cm diameter pipe is 10 L/min, * the flow rate in the other pipe is 3.3 L/min O 10 L/min O 40 L/min 56.6 L/min O 100 L/min

Consider a pipe that branches out into two parallel pipes and then rejoins at a junction downstream. The two parallel pipes have the same lengths and friction factors. The diameters of the pipes are 2.5 cm and 5 cm. If the flow rate in the 2.5 cm diameter pipe is 10 L/min, * the flow rate in the other pipe is 3.3 L/min O 10 L/min O 40 L/min 56.6 L/min O 100 L/min

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An orifice with a hole diameter of 90 mm is attached to the cross section of a 180 mm diameter pipe through which air passes. The pressure drop across the orifice with a discharge coefficient of C = 0.62 is 80 mmSS. Since the density of the air is 1.2 kg / m3 and the density of the water is 1000 kg / m3, what is the flow rate of the air passing through the pipe in kg / s?
For the flow of fluid at a Reynolds number of 4 x 106 through a 5-cm pipe with a roughness factor of 0.005 mm, what is the Darcy friction factor? O 0.0304 0.0148 0.0124 0.0000160 0.0197 QUESTION 14 You want to insert a valve into a 2.5 inch diameter piping system with a flow rate of 9 ft/min. If you can accept an additional head loss of no more than 2 ft from adding this valve, what is the largest loss coefficient KL you can permit when searching for your valve? O 0.150 6.65 2.03 0.207 1.85
A liquid food (p = 900 kg/m³, µ= 2 cP) flows from a 15 m long pipe of 3-in. diameter to a 25 m long pipe of diameter 9-in. at the rate of 125 kg/min. Determine the following if both pipes are made of wrought iron (ɛ = 45.7x10°m): a. Average velocity of the fluid in both pipes b. Reynolds number in both pipes c. Kinetic energy correction factor in both pipes d. Energy loss due to friction in both pipes e. Energy loss due to expansion in pipe diameter
Water at 59 F flows through a straight section of a 6-in-ID cast-iron pipe with an average velocity of 4 fps. The pipe is 120 ft long, and there is an increase in elevation of 2 ft from the inlet of the pipe to its exit. Find the power required to produce this flow rate for the specified conditions. Solve for the fanning friction factor
Fluid flows through a pipe with 2 elbows and a valve for which the values of K are 1 and 5, respectively. If the diameter of the pipe is 0.1 m and the fluid velocity is 0.29 m/s, the minor losses through the pipe would be 0.025 m O 0.03 m 0.04 m O 0.05 m
PLease refer to image tq
The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water from a pump to a reservoir whose water surface is 107m higher than the pump. Water is pumped at the rate of 0.07 m³/s. Determine the horsepower saved by replacing the old pipe with a new 250mm pipe. Assume the value of f as equal to 0.033 and 0.022, respectively, for the old and new pipes. Neglect losses of head except friction head.
Water at 15°C is transported from a large open tank to the bottom of another open tank above. The surfaces of the two tanks are kept at 160 ft apart vertically. The pipes used have an ID of 3.5 inches, and a total length of the pipe used is 150 ft. In the system, there are two fully open gate valves, 6 90° elbows, and 2 standard tees. The pump used has a mechanical efficiency of 60%, and the volumetric flow rate of water is at 35 (ft^3)/s. Frictional losses due to sudden contraction and expansion are negligible. Determine the Reynolds number of the flow
Consider a pump system that delivers water at a flow of Q = 5 cubic feet per second (cfs) in a steel pipe (ɛ = 0.00020 feet) between two large open reservoirs. The diameter of both the suction pipe and the discharge pipe is D = 12 inches. The friction factor is f = 0.015646. The total length of the pipe is L = 1,525 feet. The water surface elevation of the receiving reservoir is 80 feet higher than the water surface elevation of the supply reservoir so (z2 – z1) = 80 feet. The water temperature is 50°F. The kinematic viscosity of the water is 1.41 x 10 5 ft2/s. The efficiency of the pump is 68% and the efficiency of the electric motor is 88%. Use the Darcy-Weisbach equation to evaluate the friction head loss. Also, evaluate the minor head losses. The pipe section on the suction side of the pump and has a diameter of D1 = 12 inches, a length of L1 = 25 feet, and a friction factor of f = 0.015646. The entrance from the reservoir into the suction pipe is a projecting entrance. Then, there…
A water distribution system is supplied from a water reservoir with a bent pipe as shown in the figure. The pipe friction factor f is 0.024. Ignoring all minor losses, the Velocity in the pipe is. d = 100 mm 25 m O a. 11.4 m/s а. O b. 15 m/s 150 m Ос. 3.4 m/s O d. 2.14 m/s
Water is transported by gravity through a 10-cmdiameter 550-m-long plastic pipe with an elevation gradient of 0.01 (i.e., an elevation drop of 1 m per 100 m of pipe length). Taking ? = 1000 kg/m3 and ? = 1 × 10−6 m2/s for water, determine the flow rate of water through the pipe. If the pipe were horizontal, what would the power requirements be to maintain the same flow rate?