Consider a medium in which the heat conduction equation is given in its simplest form as: 1 a ƏT 1 ƏT r² ər ar a dt (i) Is heat transfer steady or transient? (ii) Is the heat transfer one-, two-, or three-dimensional? (iii) Is the heat generation in the medium? (iv) Is the thermal conductivity of the medium constant or variable?

Consider a medium in which the heat conduction equation is given in its simplest form as: 1 a ƏT 1 ƏT r² ər ar a dt (i) Is heat transfer steady or transient? (ii) Is the heat transfer one-, two-, or three-dimensional? (iii) Is the heat generation in the medium? (iv) Is the thermal conductivity of the medium constant or variable?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heat conduction What does the assumption of one dimestional heat conduction mean? In the conduction what actual phenomena (heat transfer mechanisms) are being ignored to assume it, and where do they occur?
Write the heat rate equation only, don’t evaluate. Using table 4.1 in “Introduction to Heat transfer, 6th ed., Wiley”
A mectal cylinder of 5 cm in diameter and initially at a temperature about 150 °C. the eylinder is suddenly immersed in liquid with temperature at 50 °C and heat transfer coeflicient about 2000 W/m.°C. Under typical operation conditions the center temperature and surface temperature are measured to be 110 °C and 90 °C after 1 minute, respectivielly. Calculate the thermal conductivity for this material.
Please provide one-dimensional heat conduction equation in a sphere starting from energy balance for a system.
Discuss the general procedure for finite element analysis of physical problems. How does FEA differ from exact solutions approach for solving boundary value problems in engineering?
This question requires the use of the conduction charts given in the appendix at the end of this paper. A wooden sphere of diameter 5 cm is initially at a uniform temperature of 21 °C. Its surface temperature is suddenly raised to 83 °C. The thermal conductivity and thermal diffusivity of the wood are 0.15 W/m K and 0.82 x 10-7 m2/s, respectively. a) Calculate the temperature 2 cm beneath the surface of the sphere 30 min after the sudden increase in temperature. b) Calculate the energy gained by the sphere during this time.
1.14 Two hydraulic cylinders are used to control the position of the robotic arm ABC. Knowing that the control rods attached at A and D each have a 20-mm diameter and happen to be parallel in the position shown, determine the average normal stress in (a) member AE, (b) member DG. 400 mm E -300 mm- A F 150 mm 150 mm 200 mm B 600 mm- 800 N C
Please solve quickly
Qs A wall separated hot water from cold air in order to increase the heat transfer rate a number of fin s are added to air side. The heat transfer coefficient on the water side is 255 W/m K and on the air side is 57 W/m K, the thermal conductivity is 3 W/m.K. The surface area the wall 3 m × 0.6 m and the fin length is 125 cm with thickness of 0.5 cm if the number of fins are 96. determine the rate of heat transfer by adding the fins. Ans: 7484 W
A flat plate in an ambient at temperature Tꝏ received from a source the net radiant heat flux q” (fig. 3-52). The thickness of the plate d is much less than its length 2L; the third dimension of the plate extends to infinity. The heat transfer coefficient from the ends of the plate, if needed, may be taken to be h3 ≠h1 ≠h2. Find the temperature distribution in the system. Please type answer note write by hend.
Write down the Fourier heat conduction equation and explain the meaning of each term in the equation in units. Find the heat conduction coefficient of a cylindrical material with a diameter of 25mm, a length of 30mm, temperatures of its two surfaces T1 = 40.2oC, T2 = 38.9oC, respectively, and a given thermal power amount of 22.4W.
pls ans quickly