Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an area of A;= 0.8 cm? and A2= 0.04 m². Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. F1 A2 Hydraulic oil SG = 0.870 Aj F2 At the beginning, when both pistons are at the same elevation (h= 0), calculate the force F1 in newtons required to hold the weight of the car.

Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an area of A;= 0.8 cm? and A2= 0.04 m². Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. F1 A2 Hydraulic oil SG = 0.870 Aj F2 At the beginning, when both pistons are at the same elevation (h= 0), calculate the force F1 in newtons required to hold the weight of the car.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
The hydraulic press shown in Figure 9 is filled with oil with sp.gr. 0.82. Neglecting the weight of the two pistons, what force F on the handle is required to support the 10 kN weight? 75 mm Ø Hinge 10 kN oil 25 mm | mm| Figure 9 400 mm 25 mm Ø F
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to Patm H 424 Hg:
Fluid Mechanics (question 5)in the solution can you provide the conversion/s (if neccessary to the question) so I could understand how to solve it better
How to solve this question . Step-by step solution needed with explanation. ( Fill in the Blank)
Given The tank shown has one curved surface restraining a body of static fluid, with the following dimensions: w- 5.00 m h1 = 2.5 m R1 = 0.85 m Required Determine the value of x-bar in metres, to the nearest 1000th. Water hl R1
Q 1 A
In a hydraulic press, the ram has a diameter of 20 cm and the plunger 2 cm. The fluid is an oil of specific gravity 0.8. Calculate the mass that can be raised by placing a mass of 100 kg on the plunger: (i)When the plunger and the ram are on the same horizontal plane, and (ii)When the liquid level in the plunger is 0.5 m above that in the ram. What is the mechanical advantage of the press in cases (i) and (ii) above?
Read the question carefully and give me right solutions with clear calculations
IV. Water is discharged from a device in to air, as shown in the figure. How much is the horizontal force to hold the device. Ignore gravity and viscosity. 1 Ibf= 1 slug ft/s 2, air (2)A=0.4 t 30 fU 10 psi Flang 1/20 tis (1) A=0.8 (E) A- 0.8 n air Water density =1.94 slugs/ft^3.
1. A nurse applies a force of 4.40 N to the piston of a syringe. The piston has an area of 6.56 x 105 m². What is the pressure increase in the fluid within the syringe? kPa
Q4: A 7-cm diameter solid aluminum ball (SG = 2.7) and a solid brass ball (SG-8.5) balance nicely when submerged in a fluid as shown in figure. a) If the fluid is water, what is the diameter of the brass ball? b) If the brass ball has a diameter of 3.8 cm, what is the density of the fluid? 2 pulleys Fluid brass aluminum D= 7 cm +