Consider a damped mass-spring system with mass 3 kg, spring constant 10 N /m, and damping coefficient 5 kg/s. At t = 0, the mass is displaced a distance 0.7 m from equilibrium and released from rest. How long (in seconds) would you have to wait until the mass completes ten oscillations? In other words, how long do ten complete oscillations take?

Consider a damped mass-spring system with mass 3 kg, spring constant 10 N /m, and damping coefficient 5 kg/s. At t = 0, the mass is displaced a distance 0.7 m from equilibrium and released from rest. How long (in seconds) would you have to wait until the mass completes ten oscillations? In other words, how long do ten complete oscillations take?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2-kg block attached to an Ideal massless spring and fixed on the other end on a horizontal frictionless surface. This block oscillates with an amplitude of 0.5 m and reaches a maximum speed of 2 m/s. What is the spring constant in N/m?
A block of mass m = 5 Kg is attached to a spring of spring constant k. The block oscillates in simple harmonic motion on a frictionless horizontal surface. The block-spring total mechanical energy is 14.4 J. The maximum velocity of block, vmax, is
An object attached to the end of a vertical helical spring bounces with a frequency of 2.1 Hz. If the spring constant is 5.9 N/m, what is the mass of the object?
A 0.1 kg object oscillates as a simple harmonic motion along the x-axis with a frequency f =3.185 hz. At a position x1, the object has a kinetic energie of 0,7 j and a potential energy 0,3 j. The amplitude oscillation,A,is?
The spring-damper-mass system shown in Figure Q3(c) is at rest when strict bya hammer with an initial velocity of 0.4 m/s causing the mass to move upwards.Given that the mass m = 2 kg, spring constant k = 128 N/m and coefficient ofviscous damping c = 0.6 Ns/m.(i) Determine the damped frequency of the spring-damper-mass system.(ii) Base on the given conditions derived in Q3(c)(i) and parameters givenabove, describe how you would derive the equation of motion ofdamped-free vibration.
A 1-kg block attached to an Ideal massless spring and fixed on the other end on a horizontal frictionless surface. This block oscillates with an amplitude of 0.3 m and reaches a maximum speed of 5 m/s. What is the spring constant in N/m?
The logarithmic decrement of damping of a tuning fork oscillating with a frequency 1,1 Hz is 5. After what time interval will the amplitude of the tuning fork oscillations decrease by 7,1 times? Assume that the period of damped oscillations is close to the period of free undamped oscillations.
The complete slide- back and forth motion of a single reciprocating compressor piston completes in a 2-sec period. The volume displacement of the piston though the piston cylinder is 8,902.63 in3. The stiffness of crank is said to be equal to 65.5N/m and the mass of the said piston is at 10kgs. A.)Draw out your conclusion of the vibration found during the motion of the piston through its piston cylinder.
Given an oscillator of mass 2.0kg and spring constant of 180N/m, what is the period without damping? Use numerical methods to model this oscillator with an additional friction force equal to where c is a positive damping constant. Using c=5.0, what is the new period of oscillation. What about for c=10? Assume initial position is 0.2m and initial velocity is zero. Please find the period using the position versus time plot and use the first full cycle of the motion.
A mass m = 4 kg is attached to both a spring with spring constant k = 101 N/m and a dash-pot with damping constant c = 4 N. s/m. The mass is started in motion with initial position xn = 5 m and initial velocity vn = 3 m/s Determine the position function x(t) in meters. x(t) Note that, in this problem, the motion of the spring is underdamped, therefore the solution can be written in the form æ(t) = Cje pt cos(wit – a1). Determine C1, wi ,ajand p. C = (assume 0 < aj < 27) p = Graph the function x(t) together with the "amplitude envelope" curves a = -Cje-pt and r = Ce-pt Now assume the mass is set in motion with the same initial position and velocity, but with the dashpot disconnected ( soc = 0). Solve the resulting differential equation to find the position function u(t). In this case the position function u(t) can be written as u(t) = Cocos(wat – ao). Determine Co, wo and aæn. Co = wo = (assume 0 < an < 27 ) Finally, graph both function x(t) and u(t) in the same window to illustrate the…
Y2
QUESTION 3. Consider the mass-spring oscillator without friction: y" + y = 0. Suppose we add a force x(t) which corresponds to a push (to the left) of the mass as it oscillates. We will suppose the push is described by the function x(t) = -u(t – 2n) + u(t – (2n + a)) for some a > 2n which we are allowed to vary. (A small a will correspond to a short duration push and a large a to a long duration push). Here, u(t) is the unit step function. We are interested in solving the initial value problem y" + y = x(t), y(0) = 1, y'(0) = 0.