Consider a converging nozzle with a low velocity at the inlet and sonic velocity at the exit plane. Now the nozzle exit diameter is reduced by half while the nozzle inlet temperature and pressure are maintained the same. The nozzle exit velocity will (a) remain the same (b) double (c) quadruple (d ) go down by half (e) go down by one-fourth

Q: CO, enters a nozzle at a mass flowrate of 5000 kg/hr at a pressure of 200.0 kPa, a temperature of…

A:

Q: Helium expands in a nozzle from 220 psia, 740 R, and negligible velocity to 15 psia. Calculate the…

A: Consider the diagram shown below for the nozzle. Since the inlet velocity is negligible, the inlet…

Q: A lump of steel of mass 8 kg at 1000K is dropped in 80 kg of oil at 300K. Make calculations for the…

A:

Q: Q-3/A vessel is divided equally in two parts. The first part is evacuated, while the second part of…

A:

Q: What would the nozzle pressure (in kPa) be if the sonic flow with Helium in the nozzle has a total…

A: A nozzle is mechanical equipment where the pressure energy of the working fluid gets converted into…

Q: 4. It is important to remember that the isentropic relations and normal shock relations are…

A: To determine the Mach number of the given total temperature static pressure is  and to determine…

Q: The air in a piston-cylinder assembly is compressed with a pressure of 90 Kpa and a reversible…

A:

Q: A large reservoir maintains air at 6.8×105 P a and 15°C. The air flows isentropically…

A:

Q: The mass flow rate of gas entering nozzle is 25 /m3 . The inlet total pressure= 200kPa and inlet…

A: The total inlet pressure, P1 = 200 kpaThe total temperature, T1 = 900 KThe exit pressure, P2 = 80…

Q: Q-3 / A vessel is divided equally in two parts. The first part is evacuated, while the second part…

A: Given data in second part of container  mass of compressed liquid (m)  = 2.5 kg  Initial Pressure…

Q: Given the temperature of the sink, the change in entropy and the effective work done by Carnot…

A:

Q: Q-3/A vessel is divided equally in two parts. The first part is evacuated, while the second part of…

A: Given ; T= 333 K , P1 = 4 bar ,P2 = 40 KPa

Q: Steam at 228 and with a specific entropy of 6.1351 kj/kg-k undergoes a poly tropic process with…

A:

Q: An ideal gas enters a turbine with a velocity of 40 m/s through an inlet pipe with a diameter of 160…

A: As per the guidelines, I can answer only first three sub-parts. For rest parts please re-post again.…

Q: The gain in entropy during an isothermal non-flow process of 5 lbm of air at 60F is 0.462 BTU/R.…

A: Given → T1= T2 = 60 F = 519.67°R                  ds = 0.462 BTU/R , m = 5 lbmFor air →CP = 0.24…

Q: Consider a converging nozzle with sonic speed at the exit plane. Now the nozzle exit area is reduced…

A: Maximum mach number that can be achieved in a converging nozzle is unity, unless there is any…

Q: Air enters a frictionless duct with V₁ = 70 m/s, T₁ = 600 K, and P₁ = 350 kPa. Letting the exit…

A: To Find : The entropy change at intervals of 200 K. Given : The inlet velocity is v1=70 ms The…

Q: In a convergent divergent passage normal shock wave forms in the divergent section. The entropy…

A: 1) After the shock wave the randomness of the molecules increases. 2) So, the velocity will increase…

Q: onsider a converging nozzle, with exit air velocity of Ma=1.

A: We have  a converging nozzle, with exit air velocity of Ma=1.

Q: A gas turbine nozzle has a pressure ratio of 1.8. The initial pressure and temperature are 3.5 bar…

A: Given DataP1=3.5 barT1=1050KV2=548 m/sR=287J/kgKγ=1.4rP=1.8

Q: . If 10 kg/min of air are compressed isothermally from p1 = 96 kpa and V1 = 7.65 m3/min to p2 = 620…

A:

Q: Air flows steadily adiabatically through a pipe with a constant cross-sectional area. Air is fed…

A: here, flow through adiabatic duct so, stagnation temperature will same at outlet and inlet.from…

Q: Steam at an initial enthalpy of 100 kJ/kg and inlet velocity of 100 m/s, enters an insulated…

A:

Q: The actual exit temperature

A: Given: Area raio=2.2 Theoretical exit temperature=260 K nozzle efficiency=0.94 To determine: Actual…

Q: High Engine Temperature Temperature (tE) in °C AS (high – low) in KJ/kgK Efficiency (c) in % Carnot…

A: Given that: For Carnot heat engine A Low temperature = 32 oC ∆S = 0.2043 kJ/kg-K WN = 57 kJ/kg For…

Q: A compressor (300 W) increases air pressure from atmospheric to 2,000 kPa. As the compressor…

A: as given that the outer casing is heated so the process is not adiabatic.

Q: It is proposed that a nozzle receive air at 2 m/s, 300 K, and 150 kPa, at temperature of 280 K, and…

A:

Q: We have steam going into a flow turbine uniform with a mass flow of 20 kg / s at 600 ° C, 5 MPa and…

A: @ 5MPa 600 Celsius , specific enthalpy = 3666.8 kJ/kg   @ 500 KPa : saturated vapor sp. enthalpy  =…

Q: he dry and saturated steam at a pressure of 10.5 bar is expanded isentropically in a nozzle to a…

A: Nozzle: It a device which increase the kinetic energy of the flowing fluid at the expense of its…

Q: 9. A nozzle is designed to expand air from 689 kPaa and 32 °C to 138 kPaa. Assume an isentropic…

A:

Q: Ideal air (mass flow rate of 10 kg/s) enters a gas turbine at 1600 (K) and exits at real conditions…

A: Given data:

Q: Air at 90 kPa and 10oC enters an adiabatic diffuser steadily with a velocity of 180 m/s and leaves…

A: Find , Exit temperature. Concept Apply steady flow energy equation between the inlet and outlet.

Q: Steam at an initial enthalpy of 100 kJ/kg and inlet velocity of 100 m/s, enters an insulated…

A: Let us denote properties of steam before entering the nozzle by subscript 1 and properties of steam…

Q: Consider a converging nozzle and a converging– diverging nozzle having the same throat areas. For…

A: For Converging and converging diverging nozzle the mass flow rates are equal at the sonic…

Q: 1 atm = 2116 lb/ft2 = 1.01 × 105 N/m2. In the reservoir of a supersonic wind tunnel, the velocity is…

A: