Condition 1 You have 2 push buttons and 1 lamp. 1. The lamp will turn “ON” if either of the 2 push buttons is pressed. 2. The lamp will turn “OFF” if both push buttons are released or both push buttons are pressed. Make an explanation of how this works.

Q: Once the LED turns on, it then has a constant forward voltage across it. Once this accurs, what kind…

A: LED is  special type of diode. Resistance of the diode comes into to picture due to the depletion…

Q: :A limit switch is usually actuated by

A: Limit switches is the mechanically operated switch. It work on the principle of the electromagnetic…

Q: QUESTION 3 The abbreviations NO and NC represent Normally Open and Normally Closed when used to…

A: Switches: Switch is a most common used electronic device. A electrical switch can normally connect…

Q: he purpose of an adjustable pressure device

A: pressure devices is in the form of switch that operates an electrical contact when a certain set…

Q: QUESTION 6 What do the individual symbols in the rung pictured represent? L1 Inputs 1/1 0-1/2 01/3…

A: PLC:- The PLC (Programmable Logic Controllers) is used to monitor the state of the input device and…

Q: A technician wants to energize a 24 volt motor, but lacks a 24 volt battery to do it with. Instead,…

A: Solution !! This is perhaps the most direct solution (setting each power supply to output 12 volts):

Q: Create an OPEN PLC V1 program that when the Start button is activated momentarily (released after…

A: Task: When the Start button is pressed (released after pressing), the bulb turns ON. The bulb…

Q: i need the answer quickly

A: Here the concept related to the Algorithm State Machine Chart (ASM-Chart) is discussed.

Q: Assume that the INTO pin is connected to a switch that is normally high. Whenever it goes low, it…

A: We assume it is asked to write a code for given information We are writing Assembly language code…

Q: Consider a system with four pushbuttons and three lamps and three motors. PB 1 is used for main…

A: Solution- Given, Consider a system with four pushbuttons and three lamps and three motors. 1. PB 1…

Q: explain the function and operation of an oil pressure switch

A: We need to explain the function and operation of an oil pressure switch.

Q: Answer in Sentence/Paragraph form. Maximum of 5 sentences each.   Lesson: Electronics: Half-Wave…

A:

Q: 22. a) Describe how the following sensors are used to measure temperature. i) RTD

A: Any system can be autonomous or manual. A system is called autonomous if the output is independent…

Q: Draw an elementary diagram of a fractional horsepower, manual motor starter

A: An elementary diagram of a fractional horsepower, manual motor starter is given below:

Q: Understand how you can use a timer to delay the start of a motor, Seal in the motor, and stop the…

A: To draw and explain the motor operated with seal in and delay

Q: 1- What type of sensor should be used in the production line given in t below figure? Explain in…

A: The system shown in figure is describes checking weather the milk carton is properly filled or not .…

Q: Activity 3: A sorting machine has three sensors, an inductive sensor, a red colour sensor, and a…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 9) Does this switch (in the open state) have a Low resistance or a high resistance between its…

A: In this question,  We need to determine and check the resistance low or high as per given the open…

Q: 3.What fundamental differences exist between ammeter and voltmeter? Illustrate and Explain.

A: Ammeter is a device that is used to measure the current in the circuit. A voltmeter is a device that…

Q: Why does the maximum power point of the solar panel shift when charging a high powered battery?

A: Reason for shifting of  maximum power point of the solar panel when charging a high powered battery

Q: Compare between servo motor and universal motor

A:

Q: Q2/ Rectifiers can be classified according to a number of different factors explain briefly.

A: Rectifier is a electrical device which is used to convert Alternating Current to Direct Current.…

Q: Write a ladder program for a system with the following control: 1. A blue lamp is ON if switch A is…

A: To create a ladder program for the given control system, we can use ladder logic symbols and…

Q: 1. Explain what are Temperature sensors and how does it work. 2. Explain what are Magnetic Switches…

A: As per the guidelines given, we can only provide the solution of one question in multiple types of…

Q: How can you shield your machine from electrical spikes?

A: The objective is to determine the way to protect the device by the voltage surges.

Q: 3. Choose the suitable sensor to detect a part inside paper box as shown in Figure 1. Figure 1 a)…

A: The capacitive proximity sensor detects only non ferrous materials with a range of 3mm to 60mm.…

Q: L 1. A single SPST switch is rated for 20 A/28V. Can this switch be used to control a 12-V, 540-W…

A: Given Data:An SPST switch with,Current rating Voltage rating Load voltage Load power To…

Q: B): Consider the measuring instrument of Digital Revolution Counter shown in the Figure 4, then…

A: The number of shafts, wheels, or other rotating objects' revolutions or rotations can be counted and…

Q: Make a circuit to control the 3-phase AC motor, such that it will turn on when the on button (NO) is…

A: Make a circuit to control the 3-phase AC motor, such that it will turn on when the on button (NO) is…

Q: Describe a small "switch" that can be turned on or off with one finger.

A: Switches are electrical device used to break or make an electrical circuit. Types of switches…

Q: About the electrical circuit using the ladder diagram (PLC Ladder)? 24G 4 G

A:

Q: Select all the the devices that can be used by the Arduino as inputs   A   Speakers B   Lights C…

A: Speaker : speaker is output device and it can not be act as input for Arduino . Light : light can…

Q: What kind of sensor is this type O a. magnetic O b. inductive O c. float O d. pressure

A: What type of sensor is given in the above image ? A. Magnetic  B. Inductive  C. Float  D. Pressure

Q: In the next figure.we want to fill the two tanks with water by a pump. The pump is operating…

A: Step 1:A diagram given states:The pump is operated manually by a push-button "Start" (normally open)…

Q: What is the mechanism of operation motion control lamp

A: mechanism of operation motion control lamp:

Q: f I were to fill in the table to have a robot follow a line being detected by the three sensors, how…

A:

Q: Compare between the three types of rectifier and which rectifier is good for conversion? justify…

A: The three types of rectifier are: Half-wave rectifier Full-wave center-tapped rectifier Full-wave…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.