Compute the steady-state momentum flux of pure ethanol at 25°C and 1 atm when the lower plate velocity (V) as shown in the figure below is 0.30 meter per second in the

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 218 MPa,…

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: 4 (7) Czar (10) 8

A: Given: There is shown a milling machine in which we have to find out the different names of the…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: Q1 (a) During construction of a highway bridge, the main girders as shown in Figure Q1(a) are…

A: The maximum bending stress in a girder due to this load is 85 MPa.

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: Write the four different types of Resultant Loadings?

A: Loading: The loading on the beam or any members is the load acting on a beam under which beam…

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the…

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m

Q: 3

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: complete 1-F on part a and b

A: Given Data: md2xdt2+cdxdt+kx=f(t)m=2 kgc=3 kg/sk=20 N/mf(t)=10 N   To Find: (a) Determine the…

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: 100 mm- 11.5 mm 7.5 mm N A 225 mm 11.5 mm (a)

A:

Q: Determine ly and ky.

A:

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: D 3.2-5. Use the graphical method to demonstrate that the fol- lowing model has no feasible…

A:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Figure Q4 shows the values of the normal and shear stresses acting on a certain stress element which…

A: Given: Normal Stress in x direction→σx=-1.5 MPa Normal Stress in y direction→σy=1 MPa Shear stress…

Q: 6xty- 2

A: Information given⇒ 6x4y-22x-1y42

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: 1- Draw Torque vs. angle of twist for steel specimen

A: INTRODUCTION : Whenever the specimen subjected to the twisting moment that is torque, the stress…

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: (4) 8.8.8.8 16 8 8 16 21

A: the question is not fully asked   bricks and blocks are given

Q: choose the correct answer 200 B. G- A Zero Force members

A: We know that if a joint with two members is not subjected t any external load and also that joint…

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: Using unity conversion ratios, show that 1.00 lbm weighs 1.00 lbf on earth

A: Given Data: The given mass is M = 1 lbm. The expression for the weight (W) is, W=Mg Where g is the…

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: Lacate the centacid of the blane sheded ora shown below

A: Given Data The radius of the quadrant is: r=16 cm The side of the internal square is: a=8 cm To…

Q: A piezometer and a pitot tube (close to each other, as described in the figure) are connected to the…

A:

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.