Compute the net area of each given members. 1. PL출X8 in Ø bolts 2. in Ø bolts W12 x 40- PL를 x 14 3. -WT15 × 45

Q: Creates a multiline text object О МТЕХТ O DIMLINEAR O QLEADER O TABLESTYLE

A: Multiline Text. The TEXT command can be used to add multiple lines of text, yet each text object is…

Q: Determine coordinates of centroid of the following shaded area. y 60 mm 20 mm 60 mm -X- 20 mm

A: Consider the given figure Calculate area of the of these two section A1=60×20=1200 mmA2=60×20=1200…

Q: In the exhibit below, What is the distance from A to C, A O 1078.57' O 1087.75' O 1187.57' O…

A: Given values: Consider closed traverse given. For closed traverse, sum of latitude and sum of…

Q: Example: reading around a 10x10 cm square area = 0.995 rev Reading around the required area = 5.765…

A: 10 cm square =0.995 rev 1 cm square=0.00995 rev area of required area=5.765 rev required area in cm…

Q: What are GNSS receivers?

A: Full form is Global Navigation Satellite System.

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 65 -190- 65 125 Dimensions in…

A: ASKED: To determine the x and y-coordinates of the centroid of the shaded area.   The given shaded…

Q: Please help me to find references or site where i can fine about Acoustic Method (Geophysical…

A: Geophysical techniques can be used to locate buried objects, chart underground utilities, and map…

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: The given shaded area in the figure below, it is the top plan of a flower garden (with a circular…

A:

Q: Draw the plan and elevation of the given line diagram. W W.C V KITCHEN D, 2100×1200 3600x2800 BATH V…

A:

Q: What information is missing in the. (answer pool : width, height, depth) 1. front view? 2.Top view?…

A:

Q: 6"

A:

Q: 5 TOP 10 8 FRONT ? Isometric View RSV

A:

Q: What are the problems faced by the ncorrect lengths of tape?

A: Tapes are widely used in surveying for measurement purpose. It is used to determine horizontal,…

Q: Find the areal scale for the following 3cm+09km

A: Given: Map distancex=3 cm Ground distanceX=9 km To find: Areal scale

Q: Level surface, Bubble line, Horizontal line, Level line, Line of collimation, Bench mark, Change…

A:

Q: 60 mm 30 mm 30 mm 45 mm

A:

Q: Q2: Draw front and side view projection for the following 36 12, 34

A: Given section: If you look at the given section from the front, the red coloured area will be…

Q: Where is the NAVIGATION BAR located, and what is it? Where is the VIEW CUBE located, and what is it?…

A: 1. In AutoCAD, the navigation bar is located on right side end of the drawing window.    The…

Q: What is seismograph?

A: Seismograph : When the tremors produce waves on the surface of the earth. These waves are called…

Q: Research on the different types of tape used in measuring distances. Give at least three examples…

A: In surveying tapes are used to measure distance it can be horizontal or vertical or inclined…

Q: [30235.294]0.8

A: Given  :-  ( 30235.294) 1/0.8

Q: Define Aerial Photographs.

A: Aerial Photographs:

Q: Q7. Describe Lithosphere

A: Everything in Earth's system can be placed into one of four major subsystems: land, water, living…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 95 125 95 -170- Dimensions in…

A:

Q: By using the figure below, reproduce this by using the relative rectangular coordinate entry. You…

A: Required To reproduce the given figure in question and to give the commands used to draw in AutoCAD.…

Q: List in tabular form, for comparison, the advantages and disadvantages of an automatic level versus…

A: Auto level: Auto level is known as self-aligning level. The auto level has a compensator which has…

Q: A blueprint for the floor of a natural history museum is shown the scale of the museum to the…

A: Given- A blueprint for the floor of a natural history museum. scale used=20 yards to 1 inch…

Q: Determine coordinates of centroid of the following shaded area.

A: Centroid is the point where the whole weight of the body acts. If the section is made up of…

Q: 20 20 FRONT ELEVATION 60 20 60

A: For given isometric view following are top, front and side views are first angle projection views

Q: What are velocity charts?

A: The Velocity Chart displays the value amount delivered in each sprint so as to forecast the work…

Q: In the exhibit below, What is the distance from A to C, A O 1078.57¹ O 1087.75' O 1187.57' O…

A: To Determine Distance from A to C, L = ?

Q: What are point positioning equations?

A: Point positioning are used for positioning with GPS. In point positioning, a GPS receiver which…

Q: Explain anti-spoofing?

A: Today's cybercriminals are continuously coming up with new strategies to enter systems and…

Q: 6. Discuss the methods of determining permeability in the field. 7. Water flows under constant head…

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: 20 kN 8 KN/m B 2 m 1 m 4 m

A:

Electrical Plans

An electrical plan is also known as an electrical drawing or a wiring diagram. It is a kind of visual representation which bears the blueprint symbols of all the electrical components in electrical house plans or various building construction projects. In other words, electrical plans describe electrical circuits and systems that build up the electrical house plans or building plans. An electrical engineer who works on various construction projects creates an electrical drawing. The engineer outlines the electric planning with different symbols and lines forming a detailed electrical circuit. These drawings are a means of representation for the clients, who will carry out the actual wiring process. In a nutshell, an electrical plan showcases the circuitry with the proper placement of electric components.