Compute the maximum service axial compression load permitted on the built-up cross-section of the accompanying figure. The load is 30% dead load and 70% live load. The steel used is A992, and the effective lengths are (KL)y = 14 ft and (KL)x = 42 ft.

Compute the maximum service axial compression load permitted on the built-up cross-section of the accompanying figure. The load is 30% dead load and 70% live load. The steel used is A992, and the effective lengths are (KL)y = 14 ft and (KL)x = 42 ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The W10 × 88 column shown bears on a concrete pedestal of the same size as the square column base…

A: W * 10 * 88 columnconcrete pedestal of the same size as the square column base platePu= 600 kips…

Q: Select an A992 W-shape for beam AB of the floor system shown in Figure. In addition to the weight of…

A: Solution; Given that; Beam spacing=5ft, Span Length=30 ft, L.L=80psf, Partial Load=20psf

Q: Given that permissible stresses are 10N/mm^2 (Tension) and 16N/mm^2 (Compression), determine moment…

Q: Determine the effective length factor for column MN of the unbraced frame shown. The loads applied…

A: Column section MN = W12x96 Beam section = W18x46 Column length, L = 13 ft Beam length = 30 ft Dead…

Q: Determine the compression design strength of an l-shaped cross section column with its cross section…

A: For A572-50 fy = 50 ksi

Q: what do columnar joint and mud-cracks have in common?

A: Like mud-cracks, columnar joints form from volume contraction. In the mud-cracks, volume decreases…

Q: Situation #2: A properties: Width, b = 400 mm 415 MPa rectangular beam has the following Effective…

Q: Design an interior span slab of a concrete floor system with the following description: Span = 10 m…

A: The slab is an important element in the structure for carrying floor load and another live load that…

Q: Use A36 steel and compute the nominal strength of the column shown. The member ends are fixed in all…

A: Ag=6.08 in2Iy=3.86 in2Ix=129 in2Fy=36 ksi Length of column, L=10 ft The nominal compressive…

Q: 3.4 Check the threshold validity below according to the bending requirement if 35MPa=m, f = 300 MPa.…

A: Dead load, DL = 5 kN/mLive Load, LL = 10 kN/mPL = 20 kNSpan, L = 4 mfc = 35 MPafy = 300 MPa3-25 mm…

Q: Wu-100 kN/m 6 m 4 m D A Question 6 (PROBLEM 2) A three-member frame ABCD is loaded with ultimate…

Q: A column 3 m long and pinned at both ends is carries an axial load of 190 kN. The column is made up…

Q: A concrete circular column with a radius of 350mm has f'c-25 MPa and is braced against sidesway. The…

A: Critical load The critical load is the maximum load that may be applied without causing lateral…

Q: Q2. Design the required tensile and compression rebars for the cross section shown below. Mu= 288…

A: for given cross section given b=250mm D=500mm MU=288KN-M FC=20 MPA FY=300MPA

Q: g flange side. The two sides of column are . And there is a supporting point at the e of column in…

Q: Analyse each of the following compression members as shown in the Figures Problem 11, to determine…

A: Given built up section Effective length = KL From code book K = 1 ( when all the members are hinged…

Q: For the cantilever beam(300x700mm) to carried the loads shown in the figure below, calculate the…

A: Cantilever beams are not flexible structural elements that are supported at one end and loose at the…

Q: Solve for the required compression steel area, A's in mm² at midspan of the rectangular beam in the…

Q: PDL = 5 KN 500 mm Wp =6 KN/m WL = 3 KN/m. PLL = 3 KN 800 mm R1 R: 2 m 1m

Q: The T-beam has an effective flange width of 826 mm and the thickness is 117 mm. If the area of the…

A: Given data: Effective flange width beff = 826 mm Thickness of flange d = 117 mm Area of compression…

Q: Determine the design strength of a T-Beam with the following data: bf = 700 mm bw = 300 mm he = 100…

Q: Find the member forces required.

A: Analysis of truss can be carried out by: method of joints method of sections. Method of joints is…

Q: A steel column is loaded with a centric normal force. The pillar is articulated in the foot and top…

A: Safety will be assessed by EUROCODE Le = Effective length = L = 6.5 m ...(As per statement given…

Q: Q2 1- Check the following weather one way or two way 2- Calculate the design ultimate load Wu on the…

A: The following figure shows the layout of slab and beams. Slab 1: LYLX=5 m3.6 m=1.389<2 Slab 1 is…

Q: (2) An 8-meter-height welded-I-section column, with pinned boundary conditions at each end, is…

A: Given: L = 8 m fy = 235 N/mm2 f = 215 N/mm2

Q: Find the value of compression Cs (in kN) if a = 163mm, d' = 70mm, fc' = 25MPa and fy = 410MPa. The…

A: Given: The value of a is 163 mm. The value of d is 70 mm. The value of f’c is 25 MPa. The value of…

Q: Select the best hot-rolled W-section for the given column

A: Calculating the factored loadfactored load=1.2Dead Load+1.6Live Load…

Q: QUESTION 5 Column Design: Given: a solid circular column carrying a compressive load of 8500 lb with…

A: SAE 4140 OQT 1000 steel

Q: Compute the maximum service axial compression load permitted on the built-up cross-section of the…

A: Built-up I Section Deal load =30% of Load Live load =70% of Load Effective length, KLy=14 ft…

Q: Does the column shown below have enough available strength to support the given working loads?Use…

A: Property of column section: Length= 20 ftE = 20232 ksi , ry = 2.3 inch, K= 1.0 , Fy = 59.0 ksi, Ag =…

Q: a. Which of the sections gives the largest allowable compressive strength? b. Which of the sections…

Q: A W21×101 is used as a compression member with one end fixed and the other end free. The length is…

A: Section-W21×101L=12 ftFy=50 ksi To find- Nominal compressive strength

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

Q: 10 kN 12 kN 4 kN 8 kN (1) (2) A 10 kN В C 12 kN D 2.0 m 2.5 m 3.0 m

Q: a) Check the section for local buckling. b) Determine the maximum compressive service load that can…

A: Given: The property of HE300B can be given as, h=300 in, b=300 in. Area, Ag = 14900 mm2. IX = 25179…

Q: An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload…

A: Given, A36 W14X605 simply supported steel beam with span “L” carries a concentrated service live…

Q: Determine the maximum possible design strength (in kN-m) of the beam

A: The values given in the question are as follows: Width of beam(b)=267 mm Effective depth of…

Q: AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is…

A: Given values: Steel column using W 14*43 section having given properties. Length, L = 10 ft fy = 50…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the design strength of a T- Beam given the following data: bf = 700 mm bw = 300 mm hf = 100 mm d = 500 mm fc' = 21 MPa fy = 414 MPa As: 5- 20 mm dia.
i need the answer quickly
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
Problem 1.A compression member is 30 feet long. It is made up of ASTM A500 Grade B (Fy= 46 ksi and Fu = 58 ksi) rectangular HSS 12x8x3/16. Assume k-value equals to 1.0 and Q= 1.0 . If the member carries an axial load composed of 26 kips dead load and 77 kips live load, is the member adequate? Use E=29000 ksi. a. Solve for the gross area.b. Compute for the design strength against squash load.c. Solve for the moment of inertia and radius of gyration for both axes. (X-X and Y-Y)d. Compute for the design strength against global buckling.e. Solve for kL/rfor both axes.(X-X and Y-Y)f. Solve for Fcr.g. Solve for design strength against local buckling.Check first if Local Buckling is applicable.h. Compute for the ultimate load to be carried by the member. Use LRFDLoad Combination.i. Does this member have enough strength? Why or why not?
Steel structure-Civil Engineering please answer the 5th question .
Solve it
Typewritten for upvote. Thank you
Figure 1 shows the cross-section of a heavily welded I-section steel column under axial compression. The yield stress of the steel section is 300 MPa. (a) Check the slenderness of the flanges and webs. (b) Determine the effective and gross areas of the cross-section. (c) Determine the design axial capacity of the cross-section. 380 E 10 425 -8 Figure 1. Cross-section of the rectangular hollow section steel column (Units: mm)
Please Determine the axial load strength and moment (without and with reduction factor) a square columns for the following conditions and draw their interaction diagrams (note the scale): When conditions are in balance During the tensile condition When the pressure condition Pure axial Pure moment
A compression member AB (HE 400 B) is pinned at both ends and braced in the weak direction as shown in the figure. Material and geometrical properties are given below. For the given loading and ASD load combination (PG+Pq=3500 KN), determine whether the section is satisfactory or not. Material: 5355 F355 MPa F 510 MPa E= 200000 MPa Section properties (HE 400 B): A: 19780 mm² d: 400 mm h: 298 mm t: 13.5 mm. tr: 24 mm b: 300 mm i,: 170.8 mm İy: 74 mm B X -BRACING IN THE WEAKDIRECTION
Compute the total elongation of the tapered steel bar shown in Fig. 5 subject to an axial load P (= 80 kN). The bar is of constant thickness 12 mm and tappers from W¡ mm at left to w2 mm at the other end. Given E=200 GPa for steel. Values of w1 and w2 for different Roll numbers are stated in Table below. What axial stress exists at mid-length section? Last digit of W1 W2 Roll No. (mm) (mm) P P 1, 4, 7 2, 5, 8 40 120 50 140 12 m 3, 6, 9 & 0 60 160
Determine the design strength of a T- Beam given the following data: b = 700 mm by = 300 mm hf = 100 mm d = 500 mm fe' = 21 MPa fy = 414 MPa As: 5- 20 mm dia.