Compute the maximum acceptable service load on an A36 steel plate tension member 1/4 in. x 12 in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8-in.-diam bolts are used

Compute the maximum acceptable service load on an A36 steel plate tension member 1/4 in. x 12 in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8-in.-diam bolts are used

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Related questions

Q: 1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts.…

A: Plate 130 mm x 25 mmbolt diameter, db = 20 mmA36 grade of steel:fy = 250 MPafy = 400 MPaTo find:a)…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: LRFD It applies Ultimate factored loads to design. Evaluate forces and stress using yielded…

Q: NEED ANSWER URGENT PLS!! A W 12 x 35 tension member of A992 steel (Fy = 350 MPa and Fu = 450 MPa) is…

Q: 4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with…

A: Tension member UPE 300 bolted connection. Fy = 275 N/mm2 Fu = 430 N/mm2 Ag= 5660 mm2 tw= 9.5 mm

Q: o normal temperatures but wet in-service conditions. Assume =0.95 and the geometry factor is CA=1.…

A: 1 Area of the plate Ag Ag = 4×10 = 40 in2for A36 grade steel fy =36000…

Q: The bolt group shown in Figure P consists of 3⁄4inchdiameter, Group A bearingtype bolts in single…

A: Solution Given Data Diameter= 3/4 inch

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: Given: Diameter of bolt= 1 inch ( Group A ) Diameter of bolt hole= d0 =116+1=1.06 inch Plate…

Q: Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in…

A: Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Q: A double-channel shape, 2C8 x 18.75 is used as a tension member. The channels are bolted to a 38 -…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

Q: A single-angle tension member, an L4×4×3/8, liameter bolts as shown in the attached figure is…

A: L4x4x3/8 d= 7/8 in do= 1 in

Q: 4. Determine the service load capacity of 2C10X20 channels as a truss member attached to a 7/8 in…

A: Grade of steel= A572 grade 65. Hence, yield strength= fy = 65.3 ksiUltimate strength fu = 79.8 ksi…

Q: Compute the design strength ($Pn) of the double angle tension member shown below for the following…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: Design strength for tension on gross area=∅Rn For LRFD, ∅Rn=0.75Rn Tension on gross area=Rn=Fy×Ag…

Q: Determine the allowable tensile force P which can be appllied to the plates shown. The AISC…

A: Diameter of bolt, Thickness of plate, Width of plate, To find: Allowable tensile force.

Q: Delermine the available axial compressive strength by each of the following methods: a. Use AISC…

A: Given Data -

Q: A Single Angle Tension Member L 4"x4"x 10mm is connected to a gusset plate with 7/8" diameter bolts…

A: Data Given: L 4" × 4" × 10mmBolt diameter = 7/8"DL = 30 kipsLL = 20 kipsEffective net area = 90%…

Q: The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter.…

A: Following are the given information. Member =58×10 Steel A36 → Fy=36 ksi → Fu=58 ksi Bolts are 78…

Q: An L 5 x 5 x tension member of A588 steel is connected to a gusset plate with six -inch- diameter…

Q: loads shown. Does this member have enough strength Assume that . a) Per LRFD b) Per ASD

A: For grade A 36,Dead load =95 kipsLive load =9 kipsNeed to findDoes member have enough strength.(a)…

Q: The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely…

Q: 5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer In order to calculate the minimum acceptable tensile service load we need to first find the…

Q: Three steel bolts are to be used to attach thesteel plate shown to a wooden beam. Theplate will…

Q: Governing Ultimate Tensile Capacity based on Yielding of gross section

A: Gross area Ag=11.2 in2Yield stress Fy=50 ksiUltiate stress Fu=65 ksiy¯=3 inLength of weld L=12…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single see section that is…

A: Solution: Given: Steel section: WT 12 x 47 Gross area = 13.8 in2 x = 2.99 in Length of connection:…

Q: 8.20 A column section ISHB 300 @ 618 N/m (f, = 410 N/mm2 mand f, = 250 N/mm?) is to be spliced. The…

A: For solving this problem we have to columned to be machined which is for the complete bearing and…

Q: A bracket must support the service loads shown in the figure below. The loads act through the center…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: Given:Diameter of bolt= 1 inch ( Group A )Diameter of bolt hole= d0 =inchPlate thickness=t =…

Q: A C8 x 11.5 is connected to a gusset plate with 7/8-inch-diameter bolts as shown in Figure P3.2-3.…

A: Given Data: For grade 50 A572 Fy=50 ksi Fu=60 ksi t=0.75 m For the given channel section from manual…

Q: The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the…

Q: A C8 x 11.5 is connected to a gusset plate with 7/8 inch diameter bolts as shown in Figure P3.2-3.…

A: Solution For grade 50 A5672Fy =50 ksiFu=65 ksit=0.75Ag=3.37 in2.tw=0.22 in

Q: Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle…

Q: 2. A single-angle tension member, an L3 x3 x3/8, is connected to a gusset plate with 22mm- diameter…

A: Given data L 312x312x38 diameter of bolt = 22 mm A (36 steel) Service Dead load = 155 KN Service…

Q: Q14 What is the available tensile strength of a WT 20x74.5 made of A572 grade 50 steel? Use ASD,…

Q: A MC230x35.6 connected to a gusset plate with 24 mm diameter bolts as shown. The steel is A572M…

Q: A double angle 2-L152x152x15.9 is connected to a 16mm gusset plate as shown. The bolts are M22,…

A: Given data: Double angle of 152*152*15.9 Thickness of gusset plate=16 mm Fy=345 MPa for angle…

Q: A PL3/8"X6" tension member is welded to a gusset plate as shown in the figure. The steel…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is connected to a gusset plate at its flange using welds that is 15 inches long as shown in the figure. The service live load is three times the dead load and the earthquake load is assumed to be 10% of the dead load. Use A992 steel with Fy-50 ksi and Fu 65 ks. Design in LRFD ONLY, and no block shear will occur. WT 12x47 WIL 47 A= 13.80 d 12.3 (312) weldi 0.550 (140) 9.00 (229) 0.500 (249) 1.3800 186.00 20.30 3.670 bf-9.00 (229) y=2.99₁ 0.980 (24.9) y= 2.990 y 54.50 Sy 12.00 1.960 d=12.3 (312) X 2,620 a. Governing ultimate tensile capacity based on yleiding of gross section in kips Round your answer to 0 decimal places. Add your answer tw of= of k= Sx= EX tw=0.550 (14.0) ⠀
I vll upvote.....Asap plz
2. A single-angle tension member, an L3x3 x3/8, is connected to a gusset plate with 22mm- diameter bolts as shown in the figure. A36 steel is used. The service loads are 155KN dead load and 66 kN live load. Investigate this member for compliance with the NSCP 2015 Specification. Assume that the effective net area is 85% of the computed net area. Consider yielding of the gross section and fracture of the net section. Neglect block shear. a. Use LRFD. b. Use ASD L3½x 3/2 x% Section
4. Determine the service load capacity of 2C10X20 channels as a truss member attached to a 7/8 in gusset plate as shown in Figure e5.20. The steel is A572 Grade 65 and the 7/8 in diameter A325 bolts are in a bearing-type connection (A325- X) with no threads in the shear planes. The load is 25% dead load and 75% live load O 4@3-1-0 O C10 x 20
Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is connected to a gusset plate using welds 12 inches long, as shown in the figure. The service live load is three times the dead load. Use A992 steel. USE LRFD ONLY, no block shear will occur. What is the Maximum Tensile SERVICE Load Round your answer to 3 decimal places.
Q14 What is the available tensile strength of a WT 20x74.5 made of A572 grade 50 steel? Use ASD, assume a shear lag factor (U) of 0.75, the connections are welded, and neglect block shear or other Chapter J requirements. Check both yielding and rupture. a) 800 kips b) 986 kips c) 533kips d) 656 kips
4. The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely support a service dead load of 265 kN and a service live load of 555 kN. L 50 102.5 102.5 50 65 65 65 O O 22 veny diameter bolts C310 x 30.8 Iso A36M stool matorial and select a double anglo tonsion member to rosist
Hi! Please answer this question. Thank you!
Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in the plane of shear. The plates 3/8 x 7 and 5/16 x 7 are made of A36 (F,=58 ksi) steel. If live load to dead load ratio is 4, find the maximum service load that the connection can carry. A325X % in diameter bolts PL 3/8 x 7 PL 5/16 x 7 1.5 in 2 in 2 in 1.5 in 1.5 in 2 in 2 in 1.5 in
need answer and how to solve thank you
Please answer
1. A Single Angle Tension Member L 4"x4"x 10mm is connected to a gusset plate with 7/8" diameter bolts shown below. A36 Steel is used. The service loads are 30kips DL and 20 kips LL. Investigate this member for compliance with AISC Specification. Assume that the effective net area is 90% of the computed net area. a) Use LRFD. b) Use ASD. L3'/½× 3'/½× ³3/8 Section