Compute the mass ordinate of sta 0+020 using a shrinkage factor of 1.30 from the following tabulation of volumes of cut and fill between stations 0+000 to sta 0+ 140 : sta 0+000: Vol cut= 50 cu m ; sta 0+020:Vol cut= 100 cu m ; sta 0+040: Vol cut= 80 cu m ;sta 0+ 0+060 : Vol fill= 120 cu m;sta 0+080: Vol fill=60 cu m; sta 0+100: Vol fill =40 cu m ; sta 0+120 : Vol cut =20 cu m sta 0+140: vol cut = 30 cu m

Compute the mass ordinate of sta 0+020 using a shrinkage factor of 1.30 from the following tabulation of volumes of cut and fill between stations 0+000 to sta 0+ 140 : sta 0+000: Vol cut= 50 cu m ; sta 0+020:Vol cut= 100 cu m ; sta 0+040: Vol cut= 80 cu m ;sta 0+ 0+060 : Vol fill= 120 cu m;sta 0+080: Vol fill=60 cu m; sta 0+100: Vol fill =40 cu m ; sta 0+120 : Vol cut =20 cu m sta 0+140: vol cut = 30 cu m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Derive the "bulk density" and "voids" formulas?
For the founndation shown below, determine the dimensions for effective length, L’, and width, B’.
Determine the uniformity coefficient and coefficient of gradation from the following data:
Using the design chart below. Estimate the SN if W18=10x10^6, R=90%, So=0.35, Mr- 10000Psi, APSI=3. Use the chart below. TL Overall standard deviation, S. Design serviceability loss, APSI 50 10 5.0 99.9 0.2 99 1.0 0.4 0.5 0.6 E 90 0.5 0.1 1.5 0.05 2.0 2.5 80 3.0 9 87 6 5 4 2 1 Example: 6.5 5.5 4.5 3.5 2.5 1.5 W18 = 5 x 106 R = 95% Design structural number, SN S, = 0.35 MR = 5000 Ib/in? APSI = 1.9 Solution: SN = 5.0 -1.0
2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top flange is 8"X 1" and the stem is 16" X1" the bottom flange is 16" X 1.5", the angle bars are 2- 5"X3"X %. Tabulate your solution and Answers. + X.
Problem 2: Given are matrices A, B, C and D. 21 -4 -26 7 -1 -2 2 -2 10 -8 A B = -1 3 -13 25 -11 -1 -1 21 -2 25 -18 1 -26 1/3 C =| -16 8. -7 D 10 -100 10y 7 -10 13 -98 1/2 22 Solve for: a) A + D b) 2C – 3A + B – 10D c) B +D - 2C + 3A d) В + D e) С - D
Please correct answer
人工知能を使用せず、すべてを段階的にデジタル形式で解決してください。ありがとう SOLVE STEP BY STEP IN DIGITAL FORMAT DON'T USE CHATGPT Design the longitudinal steel and the cross section of the beam shown, consider concrete that indicates fy = 4200 kg/(cm²), 1/2 stirrups and 2.5 cm coatings. 1m 0.5T 2m 0.2T 6.5m Calculate top rods per steel (min) asmin If f'c = 200kg/cm² 1.5T/m
The cross-section notes shown below are for a ground excavation for a 8m wide roadway. STA 18+700 7.08 0 7.57 4.06 7.27 5.79 Determine the cross sectional area at STA 18+700. Round your answer to 3 decimal places. Add your answer
A 50-m steel has an error of 0.02 m at 20°C with a pull of 50 N. A rectangular lot is to be staked out using this tape. The sides are 24.63 m and 10.65 m. The average temperature of the tape during staking out is 20°C with a pull of 50 N. The laid out area of the lot in square meters is: NOTE: Units are not required. Round-off to two decimal places.
Please solve this question in handwriting. step by step. I am confused. in details
10