Compute the magnitude of the moment Mo of the 225-lb force about the axis O-O. Assume F = 225 lb, d = 15 in., H = 11.7 in., h = 5.0 in., 0 = 40°, and o : 63°.

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

A:

Q: Determine tool life for maximum production

A: Given; Tool changing time is the time in which the tool is changed for the operation which is be…

Q: 4. Without using any software, write a G-code programme to produce the part shown in Figure 2. Take…

A: N0 G90 F0.5 S1200 T0101 M03N10 G00 X35 Z2N30 G71 U0.5 R1N35 G71 P36 Q90 U0.05 W0.05N36 G01 X20 Z0N50…

Q: The transformation of the tool frame relative to the first frame is 100 0 Si -G 0 L 0 0 0 1 0 0 а.…

A: Given,  A single degree of freedom system.

Q: why is there no translational component for the kinetic energy of this problem? thank you!

A: here question asked that why translational component of kinetic energy is not considered?

Q: A company designs and builds cruise ships for the luxury market. Which process type does it apply?

A: Mass production is done where a lot of quantity is to be produced. Cruise ship does not fit this…

Q: Q4: State the advantage of electro polishing over mechanical polish

A: This question is based on the concept of electropolishing.

Q: Water Wheel Design You have been asked to design a water wheel that will generate electricity from a…

A: Given : To find : Mathematical model

Q: 25 mm on a layered structure of natural fibre-reinfor encountered delamination problem in the…

A: Given Data⇒   Drilling of the square hole Dimension of the hole -(20 mm×20 mm) Material of workpiece…

Q: Describe the Square matrix?

A: Square Matrix: A square matrix is a matrix having equal number of rows and columns.

Q: what process is this? what are the factor that need to consider?

A:

Q: Q1:- (a) – Give an explanation for each the following:- 1- The design mistake is very dangerous…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: ME-408 MACHINE SHOP THEORY AND PRACTICE Aside from the number of jaws, what is the difference…

A: Difference between 3 jaw and 4 jaw chuck :  1) in a 3 jaw chuck, the setting up of work piece is…

Q: need answer within 20 minutes please please with my best wishes

A: Superfinishing is different from honing in a way that:- In honing the small removable of material…

Q: 1. The torque required to move up a load using a power screw is expressed as WD₂ tan λ + f 2 1-ftanA…

A:

Q: Identify the undercuts. Illustrate cores required. • Determine Basic Complexity (rough dimensions…

A:

Q: What is planar motion?

A: Planar motion is the kind of motion where a body moves in a plane and has two degrees of freedom,…

Q: An assembly worker on a production line obtains an Allen key within reach, positions it 15 cm (6…

A: handwritten solution attached

Q: Determine tool life for maximum production

A: Given data;  Determine tool life for maximum production rate ? Where, Taylor's tool life exponent,…

Q: A selection between advanced machining operation and conventional machine operation is to be made…

A: Given dataMachining process is electrochemical machiningThinkness of stinless steel plate t=…

Q: A screw jack mechanism is to be incorporated into the machine as part of a levelling system. The…

A: Given                        Pitch, P = 6 mm                      Mass, m = 500 kg Coefficient of…

Q: metaicfhread: Pitch- 3mm thocadaryle=65 using 3-wire meltad Best size wisre diametoe ?

A:

Q: quick and right answer will get an upvote   A total of 6000 product must be produced in next 3…

A: Total number of product produced in 3 days , N= 6000 products Cycle time, tc=40sec Set up time,…

Q: A one machine shop producing bolts has a fixed cost of $2000 and a variable cost of $ 2 per bolts.…

A: solved

Q: can you resend the images as i cannot see them. thank you

A: For solution refer below images.

Q: A 1.5m mean diameter flywheel, 600 kg weight changes its speed from 240 rpm to 230 rpm during…

A: Given that, Mass of the flywheel, m=600 kg,Mean diameter of flywheel, Dmean=1.5 m,Speed of the…

Q: The tools and techniques used in CPS make the process А. fun В. enganging C. O collaborative D. O…

A: All listed answer.

Q: Q2: Can cBN be used in honing stick in single layer configuration?

A:

Q: Expound why we use CAD and its advantage to manual drawing.

A: Given CAD To find Advantage of CAD use Advantage of CAD over manual drawing

Q: Differentiate between single point, multipoint and form tool and Identify the ten examples of single…

A: Cutting tools A cutting tool is a mechanical object which is used for removing the material from the…

Q: a Buyer at Tesla and just received 18,000 tires from Michelin. The floor has discovered an issue…

A:

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: ood work on the promblem but the process is a bit hard to read, can you express

A: Given data as per question Tensile axial force, F=4500 N Outer diameter of tube, do=25 mm Inside…

Q: 16)In which process Catcher is used

A: Catcher is used in abrasive water jet machining According to question option c is absolutely correct

Q: 2. An automatic bending machine requires a very large torque and slow rpm. Suppose you are to design…

A: It is asked to reduce the RPM from 1400 RPM to 18 RPM by using spur gear combinations

Q: Machine setup steps should be stated in bullet points for ease.

A: To explain: Machine setup steps should be stated in bullet points for ease.

Q: r machining a rectangular island represented coordinates P(0,0), Q(100,0), R(100,50) and 0,50) on a…

A:

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.