Answered: Compute the discharge in m3/s of a…

Engineering

Civil Engineering

Compute the discharge in m3/s of a triangular weir, C = 0.60, e = 90 deg, H= 2.2m O 7.106 O 10.176 O 5.174 O 14.175

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The head of water on a 90° triangular weir is 0.725 ft .Compute the discharge by a) Approximate…

Q: A municipal WWTP receives 20,000m3/d of flow. They use two circular primary clarifiers operate in…

Q: A trapezoidal weir having side slope of 1Horizontal to 2Vertical discharges 50 m3/s under a constant…

A: Given data- A trapezoidal weir. side slope of 1Horizontal to 2Vertical discharge (Q) 50 m3/s…

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a a contracted rectangular…

Q: 563..After setting a 31.2 cm wide broad crested weir at a section of Padma River, got the discharge…

A: Given: Actual discharge = 600LPM Theoretical discharge = 0.0107 m3/s

Q: b. 44.760 d. 79.767 Question 1-A Question 1-B Question 1-C O Question 1-D Question 2-A Question 2-B…

Q: WHAT WILL BE THE DISCHARGED OF A RECTANGULAR WEIR IF THE HEIGHT IS 0.4m and LENGTH IS 200m…

A: Introduction : Discharge : A discharge is a measurement of how much fluid flows in a certain amount…

Q: Q7: A suppressed rectangular weir is to be built across a 4.5 m channel width to measure a flow rate…

A: width of channel =4.5mflow=1.2maximum water depth=1.2mFINDthe

Q: PROBLEM 2: Compute the flow rate over each weir. Assume Cd-0.60 1 ft 0.5 ft 60° weir plate 95cm 75cm…

A: GIVEN DATA:-⇒Cd=0.60⇒θ=60°→Formulae Used:-(1) Flow rate for triangular weir is given by:-⇒…

Q: The head on a sharp-crested, rectangular weir was incorrectly observed to be 1.8 m. when it was…

A: Given Coefficient of discharge, Cd = 0.979 Crest length, b = 4.09 m Actual head = 3.93 m Incorrect…

Q: 521.. A channel width is 0.312 m. A venture flume having a throat of 5.6 inch was set in the…

A: In this question, we will use the relation between the metre discharge and the theoretical…

Q: 23 Determine the discharge, in L/s, over the weir having a head of 0.30 m if a 90-degree triangular…

Q: The length of the weir L (in feet):

Q: 3. If there is a measured head of water of 0.60 on a 60° triangular weir, what length of Cipolletti…

A: Given,H=0.6m, Angle,theta=60°

Q: Determine the discharge (L/s) of the weir having a head of 0.851 m. if it is a trapezoidal weir with…

Q: A trapezoidal weir has a side slope of 1 horizontal to 4 vertical. The head over the weir is 2.5 ft…

Q: 10. Find the discharge over a cipolletti weir of length 1.3 m when the head over the weir is 0.65 m.…

A: This question is related to the Fluid Mechanics from Civil Engineering. In This question we…

Q: 7. The head of water over a rectangular weir is 26 cm. The length of the crest of the weir end…

A: To find discharge using Francis formula

Q: Determine the head (in meters) on a 25 degrees V-notch weir for a discharge of 310 L/s. use Cd =…

Q: Design a weir according to the following data: Channel width = 6 m. Flow discharge = 5 m³/s.…

A: Channel width (b) = 6 m Discharge (Q) = 5 m3/sCd = 0.65

Q: Determine the discharge of the weir having a head of 0.6 m in L/s if a 51⁰ triangular weir is used.…

A: Determine the discharge of the weir having a head of 0.6 m in L/s if a 51⁰ triangular weir is used.…

Q: The discharge from a six (6) inch diameter orifice, under a 10 ft head, Cd=0.600, flows into a…

A: GIven Data:- Diameter of Orficed=6 inch Head available H = 10ft Coefficient of dischargeCd = 0.6…

Q: Q5/ Prove that the theoretical discharge over a sharp crested rectangle weir is: 2 2 theoretical -…

Q: Determine the discharge (ft3/s) of the weir having a head of 3.84 ft. if it is a triangular weir…

A: Given:- Head of the weir = 3.84 ft The central angle of the triangular weir = 69° Cc = 0.898, Cd =…

Q: 1.Water flows through a rectangular sharp-crested weir with a channel width of 2 m. The channel…

A: The given data is: Width of channel, B=2 m Channel depth, P=1 m (Height of weir plate) Head of…

Q: 3 find the discharge

A: FLUID MECHANICS

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a a contracted rectangular…

A: Given Data:Weir head = 0.30mLength = 2m It is required to calculate the discharge in L/S over the…

Q: A channel carries a head of water equal to 0.90 meters. Compute the discharge of the channel if a…

A: Given data in question Water head Angle Triangular weir Coefficient of discharge To find out…

Q: gular Weir, L = 5.55 m., Cd = 0.996 1.816 c. 44.303 3.683 d. 44.033 ular Weir, 0 = 66°, Cd = 0.904…

Q: QUESTION 8 The discharge over a trapezoidal weir is 1.315 cu.m/s. The crest's length is 2m and the…

A: Given;- Discharge, Q = 1.315 m3/s. Crest length , L = 2m. θ2= 90°-75.4°57'50''= 13.6°02'10'' Find…

Q: A trapezoidal notch having bottom width of 1.0 m is installed in a 2.0 m X 2.0 m rectangular…

A: Using relation for trapezoidal notchQ=cd2gH32[23B+815Htanθ]cd=0.64H=depth=1.5mTop width=2mBottom…

Q: Water flows through a V-notch weir in a channel 2 m wide. The channel depth is 1 m with a weir head…

Q: An unsymmetrical triangular weir with a vertex angle equal to a = 38 deg(left half) + B = 31…

Q: Find the width (meter) of a suppressed weir using the following data: H = 25.8 cm; D = 2.485 m; Q =…

A: H=25.8cm Q=0.84m3/s

Q: A 90° V-notch weir is used to measure the discharge from a spring. What is the (a) theoretical…

Q: An unsymmetrical triangular weir with a vertex angle equal to a=51deg(left half) + b=40deg(right…

A: Asked: To compute the flow rate through the weir. Given: Vertex angle for left half (a) = 51o…

Q: Determine the head (in meters) on a 25 degrees V-notch weir for a discharge of 310 L/s. use Cd…

A: Given data : Coefficient of discharge Cd=0.902 The value of discharge Q=310 l/s Angle of V notch…

Q: angular weir with a vertex angle equal to α = 40 deg(left half) + β = 26 deg(right half). What is…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Compute the discharge in m3/s of a triangular weir, C = 0.60, e = 90 deg, H= 2.2m
O 7.106
O 10.176
O 5.174
O 14.175

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Kindly answer all of it and box your answers thank you
3) b) The normal depth of flow in a 5.0 m wide rectangular channel shown in Figure 3 below is 1.0 m. The channel is laid at a slope of Im/km and has Manning's n of 0.02. Calculate the discharge and velocity in this channel associated with normal flow conditions. c) At a point downstream of that in part (b) above, there is a weir, Az is 0.5 m in height. If the section properties of the channel remains the same as in part (b), determine yı the depth of flow just before the weir. Assume negligible headloss across the weir and critical flow occurs over the weir. (yı lies between 1.2- 1.3 m) YA AZ Y2 Y2 for Q = const AZ Figure 3- Question 3 (b) and 3 (c)
A channel carrying 105.86 ft³/s. Assuming that an error of 0.05904 in is made in measuring the head, determine the resulting percentage of error in discharge. (a) If a 90º triangular weir is used. (b) If a Cipolletti Weir 10ft long is used. Draw the sketch
Q13: A sharp crested weir of Im height is fixed across 5m wide channel as shown in the following figure. The depth of flow on the upstream and downstream sides of the weir is 1.5m and 1.2m respectively. Find the discharge over the weir. y=15m H Water level W-1 m HA y = 1.2m
In 28.5 secs, 35,579 L of water is collected. The length of the rectangular weir is 2.15 m, the crest is 450 mm high from the channel bed and it should maintain a constant head of 275 mm. Determine the coefficient of discharge. Assume there is head loss.
Compute the flow rate over each weir. Indicate the appropriate unit of flow.
The head on a sharp-crested, rectangular weir was incorrectly observed to be 1.93 m. when it was actually 3.53 m. If the crest length is 4.83 meters, determine the percentage error (in percent) in the computed value of the flow rate. Use coefficient of discharge = 0.985. Round off to two decimal places.
Determine the vertex angle (in deg.) of a V-notch weir for a discharge of 29,762 L/s and a head of 4.49 m. Use Cd = 0.942. Round off to two decimal places.
Compute the discharge in m3/s of Cipolletti weir, L = 4m, H=0.8m Choices below
In 28.5 secs, 35,579 L of water is collected. The length of the rectangular weir is 2.15 m, the crest is 450 mm high from the channel bed and it should maintain a constant head of 275 mm. Determine the velocity of approach. Assume there is head loss.
9) Design a hydraulically Efficient trapezoidal section a discharge of 100 m³/sec, n=0.015 a free board of 10% of depth of flow, compute Froud number and sketch the cross section. for conveying. C So = 5000 / Assume
complete solution thankyou