Computethe allowableresisting momentused thetransformedArea methodare fc=1800Ps= f's350 mm100mm3 # 32150 mm- 24000 and n=8400 mm70 mm70 mmmm-200mmFIGURE 5.19 Example 5.17.

Calculate allowable resisting moment Working stress method Transformed area method

Answered: Compute the allowable resisting moment…

Compute the allowable resisting moment used the transformed Area method. are fc=1800 fs= f's = 24000 and n=8 350 mm 100 mm 3 # 32 70 70 - mm- 200mm FIGURE 5.19 Example 150 400

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Text: A beam is clamped at A. The beam is supported by a uniformly distributed load and a concentrated load as indicated on the sketch. The beam is made using the HE220A profile. The length of the beam is 4200 mm. and has a modulus of elasticity on it 2,0x105N/mm2 A) Calculate the bearing reactions of the beam for the given external load action. B) Establish moment and shear diagram for the beam for the given external load action. C) Calculate the transverse displacement of the free (cantilevered) end for the given external load action. D) Calculate the rotation of the free (cantilevered) end for the given external load action.
This is an alluminum I beam with a bottle jack applying load to the beam(1000 lb,2000lb etc). I attached the calibration curve as well. Basically i just want an FBD of the beam,shear diagram and moment diagram of the data. If you can use moment equations, that would be prefered. I also attached beam properties.Can someone solve this please. Thank you.
Use slope-deflection method to compute the bending moments of element ends for the following structures: 7) Use slope -defle ction Ast 4 4 12 t- 2006 Pa I= 100x 16mm" E = 200 GPa %3D I= 100× 106 mm4 For this question also compute the deflection at Point B.
5. A metric M4 x 15 square key is used with a 16 mm shaft. If the allowable shearing stress is 50 Mpa. How much torque can the assembly handle? The rotational speed of the shaft is 600 rpm. Answer: C A. 20 N-m B. 12 N-m C. 24 N-m D. 34 N-m
Compression member AB is used to hold up the 355 x 560-mm rectangular plate. If the compressive force in the member is 250 N for the position shown, determine the magnitude of the projection of this force (as it acts at point A) along diagonal OC. 355 136% 395 400 160 Answer: Foc= i 108 C B Dimensions in millimeters 145 N
■ Determine the maximum tension force T for the three cases in the figure. ■ Consider only the resistance from the angle. 100 myn 5275 tomm TEM 10mm I 1/20mm Typical хот tom томил Вотик Вэтаа Somm T T
Design the positive moment of the beam shown below, determine the number of 20mm diameter bars and the tension steel area, As. Assume the loads given are already factored. b=260mm d=420mm fe=21MPA fy=275MPA As = sq mm. n = 50KN 3m 20 KN/m
H.W. 1:An axial member consisting of two polymer bars is sup- ported at C, as shown in Figure area ol 540 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 880 mm2 and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C. . Bar (1) has a cross-sectional 50 kN Om She 35 kN (1) (2) 50 kN 0.85 m 1.15 m FIGURE
Question 5) Determine the ACI design moment capacity, Mn. Use fy = 400 MPa and f = 28 MPa. 625 mm 700 mm 4 #32 bars 175 mm, 350 mm
Determine the ultimate moment capacity of the beam with given properties below. d' = 75mm d = 380mm b = 400mm fc' = 30MPA fy 345MPA %3D As = 6- 28mm bars a. USE NSCP 2001, Mu = kN-m b. USE NSCP 2015, Mu = KN-m %3D
Hinge W B C D E Hinge 0.47 m 0.47 m 0.47 m 0.47 m 23 mm 14.7 mm A central beam BD is joined at hinges to two cantilever beams AB and DE. All beams have the cross section shown. For the loading shown, determine the largest w so that the deflection at C does not exceed 2.1 mm. Use E = 200 GPa.
pdf - Adobe Acrobat Reader DC (32-bit) in Window Help Timothy A_Philpot. Bending stress H.W. x C 다 1 /2 111% b, H.W 1 A beam is subjected to equal bending moments of M, = 45 kip ft, as shown in Figure 1a. sions (Figure1b) 6.0 in., bz = 3.0 in., and dz = 2.0 in. Determine The cross-sectional dimen- are b1 = 7.5 in., d = 1.5 in., b2 = 0.75 in., d, = K (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. State whether the normal stress at H is tension or compression. (c) the bending stress at point K. State whether the normal stress at K is tension or compression. M. d b, M. d (d) the maximum bending stress produced in the cross section. State whether the stress is tension or compression. FIGURE 1. a FIGURE 1.6 H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of the shape are shown in Figure 2 b. determine: The Consider the entire 24-ft…