Compute Ix and Iy for the region shown. 40 mm 68 mm 66 mm 66 mm 40 mm

Q: h 0.75 m 0.4 m B Fig. Q5. Q5. A plane truss subjected to loading as shown in Fig. Q5. If P = (1500 +…

A:

Q: For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and…

A:

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A: Answer: The elongation of the bar will be  ◆ When 30mm × 30mm square section : 2.22 mm. ◆ When 40mm…

Q: Question No.3 dM The bending moment M of the beam is given by dx -w(l – x) where w is a constant %3D…

A:

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Q. 2 Find the position of centroid with respect to given X and Y axis of shaded portion in the…

A: Given Shaded area To find Centroid

Q: A package-moving device is shown in the figure bellow. A. For the configuration illustrated, draw…

A:

Q: Shoe The above figure shows a component show a isometric view of a casted part which is made up of…

A:

Q: 150 200 mm D mm 150 150 v2 mm mm 0 = 45° E 12.5 rad/s

A: Given data,θ=45°ω=10 rad/sOB=1502mm=0.2155mAB=350mm=0.3556mO'A=150=0.1524m

Q: Calculate I, for the shaded region, -30- 12.5 -40 15 45 10 x

A: Given data:-section dimension lower flange length =40 mm , lower flange thickness=10 mm Upper flange…

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: For the shape below, calculate the second moment of area (moment of intertia) with respect to the…

A: Moment of area about x axis is 0.27*10-3 m4Explanation:Please find solution

Q: Determine P and RA

A:

Q: Based on the figure identify only the relative polar coordinate of each point. The answer would be…

A: In this problem, cartesian relative coordinates are given and we have to calculate the polar…

Q: A1 Neutral Axis (N.A) *:For the given data shown. the value A1 is X 200 mm 30 mm 230 mm A2 40 mm

A: Given data as per the question width of A1 =200 mm The thickness of A1 =30mm Length of A2 =230 mm…

Q: Q2) For the combined linkage mechanism shown in figure, a) Calculate the number of the degree(s) of…

A: Graphical position analysis for this problem

Q: Start this problem on a new sheet of paper The structure shown is supported by a pin at A and roller…

A: Given data is

Q: Locate the centroid of the figures shown. Calculate the moment of inertia along X and Y. All…

A: r=130 mm   To find: x,y,Ix and Iy

Q: Find the angle the surface tension film leaves the glass for a vertical tube immersed in vater if…

A: Given datad=0.25inh=0.08inσ=0.005lb/ftρ=1.94slugs/f3g=32.2ftwe know thatSurface tension force=weight…

Q: PROVE THAT THE ANGLE IS 30° BY LAWS OF CONGRUENCY

A:

Q: 11 The volume of a cube with sides of L is L. If the length is measured as 121 +2 mm, determine the…

A: Given data  The length measurement = 121+/-2 Find the worst possible error in the volume

Q: Determine yc (or y bar) for the area shown. The circle represents a hole

A:

Q: The reciprocating mass per cylinder in a 90° V-twin engine is 1.5 kg. The stroke and connecting rod…

A:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Q: Consider for the part in the figure below, a =112, b= 60 and c= 104. 80 Dimensions in mm Analyze the…

A:

Q: Q1/3-The B Rep. Scheme for the box consists of: * O 8 faces, 8 edges & 12 vertices O 6 faces, 8…

A: B rep is often known as Boundary representation. This scheme is based on the concept that a physical…

Q: HRP FRP

A: Draw the offset sectional view of the solid in the attached image.

Q: t the end of the link BC. Given the kinetic coefficie he disk is then placed against the wall.…

A: mass (m) = 17 kg angular velocity (w) = 49 rad/sec  kinetic friction (μ)  = 0.25∑ FX = FB cos 60 -…

Q: 60MPA 4OMPA Sh

A: The given plane stress is, σx=60 MPa,σy=-60 MPa,τxy=40 MPa, Steps for drawing Mohr's circle:- (1)…

Q: A rectangular lamina is of breadth 10 mm and depth 30 mm. The lg is mm Select one: O 2500 O 225000 O…

A: We have to find rectangular lamina

Q: (a) The rotating elements in machine system often generate unbalance forces due to unbalance mass…

A:

Q: Question 7a) 3 decimal points in meters * A bullet is fired at an initial velocity of 150 m/s and an…

A:

Q: The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are…

A: