Compute for the reaction at the roller B, the force components acting on the ball and-socket at A, and the value of T, if the tension on the cord CD=50kN needed for equilibrium of the quarter circular plate. (Neglect weight of the quarter circle)

Q: Use the cantilever method and determine (approximately) the reactions at supports A and B. All…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subpartsfor…

Q: A thin and weightless beam is supported by a pin connection at 4 and by a roller at B (see figure…

A:

Q: The uniform link AB, has a mass of 3 kg and is pin connected at both of its ends. The rod BD, having…

A: The given figure is shown below:

Q: Q The two-steel shaft shown in figure have the same diameter and weight 170 Ih cach. Neglect the…

A: Let the normal reaction at point C = NcThe reaction of the wall at D = N2And the reaction by wall at…

Q: E F D A Describe the load path of the applied force (of the man's weight) to the reaction points.…

A: Solution Assume man's weight = W The load path is  Its free body diagram can be  drawn as

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: Determine the reactions at A and B for the steel bar and loading shown, assuming a close fit at both…

A: Given data:- Conditions given-Remove restriction at A and solve for the reactions Below bar figure…

Q: B 1 A 1/2 IP 1/2 IP 1/2 D A frame ABCD is supported by a roller at A and is on hinge at C as shown…

A:

Q: Calculate for the degree of determinacy of the structures shown below and identify whether the…

A: Given data in question  Loading in vertical plane To find out  Degree of static indeterminacy  Note…

Q: 530 N 310 285 310 mm mm mm 325 mm 550 mm 325 mm

A: Consider the given figure. The vertical reaction at point B is By. The horizontal reaction at point…

Q: M = i R=( i kN.m i+ i j) KN

A: Given:- To find:- Moment and reaction at A

Q: 3. Determine the components of reaction at the fixed support A. Neglect the thickness of the beam.…

A: Given above given figure in Q 3 we have to find the support reactions at A

Q: 5. [AB,0A] Use conjugate beam method. (EI is constant) 22 Mo B

A:

Q: There is a small initial clearance A= 5 mm between the left end of the beam and the roller support…

A:

Q: The 8.5-kg uniform rod is pinned at end A. If it is also subjected to a couple moment of 50 Nm. The…

A:

Q: The copper pipe (G - 45GPA) has an outer diameter of 50mm and an inner diameter of 30mm, It is fxed…

A: We have to determine the value of rotation of the free end with respect to the fixed end of the…

Q: he to The structure loaded as shuwn : he 4m P 40 KN E 200 GPa 12=1c_100 x 10° mm • Solve the…

A:

Q: HW (4-1): If the area of each bar of the truss shown in 2w figure is (2700 mm') and the movement of…

A: Calculate the moment about A as; ∑MA=01×10-RD×cos4.5°×10+RD×sin45°×30=0RD=-0.707 kN Calculate the…

Q: Problem #2: 300 mm-- - 400 mm- A 13 12 60° х (N) Y (N) 5. Determine the horizontal reaction at A.…

A:

Q: Prob. 2. For the rigid frame loaded as shown, determine the reaction components using either the…

A:

Q: The analysis of shafts for a compressor is summarized by conformance to specifications. roundness…

A:

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: . In the figure below, the boom AC is supported in a ball and socket joint at C and by the cables AD…

A:

Q: Determine the reaction at support B using Force method analysis. Assume support A is fixed and…

A:

Q: Analyse the pin-jointed grame shown below using the mothod. Salect the in Gorze momber the…

A:

Q: Calculate the maximum intensity w of the uniform distributed load that can be applied on the beam…

A:

Q: ying two points loads L

A:

Q: Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the…

A: Consider the figure,

Q: From the figure below.assuming the support at A, B and C are rollers. 1.4 1.0 0.5 A Which of the…

A: Given data in question  Beam Span member length  To find out  ILD reaction co ordinate NOte We will…

Q: Draw the influence line for the vertical reaction at A. Use the analytical method in solving. Assume…

A:

Q: A steel shaft with two different diameters rotates at 4Hz. The power supplied by gear at C is 55kW,…

A:

Q: oirt B. as showm a following ignty the slope-deflection method. Sk 5 k/t S ft 8 t

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.