Compute and draw the Shear and Moment Diagram. Compute the maximum moment.

Q: Determine the maximum shear and moment for the beam shown below.

A:

Q: shearing stress in the pin at B and the axi t C are limited to 4040 psi and 5050 psi, r

A: The mechanics deals with the application of forces and reaction forces that are developed in the…

Q: 1. For the beam show below, draw its shear and moment diagram and determine its maximum bending…

A:

Q: 1/2 B cia Determine the reaction at the roller support and draw the bending moment diagram for the…

A: Given: Required : Support reaction at roller and bending moment diagram

Q: For the load group and influence line shown, P₁ = 32 kips, P2 = 32 kips, P3 = 8 kips, a = 14', and b…

A: Load, P1 = 32 Kips  Load , P2 = 32 Kips  Load , P3 = 8 kips

Q: "a" kN H 3 m "b" kN C G K 3 m "c" kN B J F 4.5 m E I 5 m 4 m

A:

Q: 25 kN/m 12m I 250KN VC B ↓ Am E-const. 8m 21 Tim

A: Given Data: To, Find: Reactions, shear force and bending moment diagram Concept: consistent…

Q: Given: The beam cross-section has the dimensions shown and a thickness of 0.5 in. It is bent about…

A: For fully plastic behaviour stress diagram is in rectangular compression and tension about equal…

Q: 4 kips w = 3 kips/ft A В C D 4'- 6'- 5'-

A:

Q: Determine the vertical reactions at A, B, C, and D. Show complete solution

A:

Q: Problem 1 The 4-in. diameter shaft shown is composed of brass 6000 ksi) and steel (G = 12,000 ksi)…

A: Given data: Shear modulus for portion AB is GB = 6000 ksi and for portion BC and CD is Gs = 12000…

Q: 4.168 A slender, homogeneous, 20-ft rod weighing 64.4 lb is supported as shown in Figure P4.168. The…

A:

Q: For the load group and influence line shown, P₁ = 8 kips, P₂ = 32 kips, P3 = 32 kips, a = 14', and b…

A:

Q: a) Solve for faevax & faosos b) Draw the shear and moment diagram.

A:

Q: A rectangular beam has a width b = 400 mm, and effective depth d = 850 mm and a total height h = 900…

A: GIVEN DATA  B=400 D=900 d=850 fck=28MPA Fy=420MPA MU=1500KN-M VU=700KN

Q: Determine the absolute maximum value of live load moment and shear produced in the 50-ft girder.

A: Given: Moving live loads and girder

Q: The pin at C has a diameter xx(see table below). Assume that the pin supports at C is stated at the…

A:

Q: positive and negative moments.

A: A simply supported overhang beam spanning over the entire length of 9 m is given. The cross section…

Q: (Problem 2.13 from the text book) Rod BD is made of steel (E=29×10° psi) and is used to brace the…

A: The FBD can be drawn as,    Given that,  Length of member BD = 54 in Young's modulus of steel, E =…

Q: 2-A distributed load is shown below. Simplify this complex load to a single force and a single…

A:

Q: For the load group and influence line shown, P₁= 32 kips, P2 = 32 kips, P3 = 8 kips, a = 14', and b…

A: An influence line diagram for shear just to the left of 40' is given. The location of P1 is 8' Load,…

Q: For the load group and influence line shown, P₁ = 8 kips, P₂ = 32 kips, P3 = 32 kips, a = 14', and b…

A:

Q: Assume that the sections have cracked, compute the bending stresses in the concrete and steel for…

A:

Q: If block AB is given a uniform load along AC and two unknown forces P and Q. If the bending moments…

A:

Q: Determine the normal stress at A and B in member CD. Pins C and D are at the centroid of the T secti…

A:

Q: A hollow steel [G= 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…

A: Given data of Hollow steel shaft :- G = 12 * 103 Ksi = 12 * 106 lb /in2 Outside diameter (do) = 3.50…

Q: Q-2 The strain in the x direction at point A on the A-36 structural-steel beam is measured and found…

A: Consider the free body diagram as;

Q: QUESTION 4) In the frame system in figure, the diameter of pin at joint B is d. The allowable shear…

A:

Q: A helical spring has a shearing stress of 120.6 Mpa with 20 turns. The spring has a deformation of…

A: Axial deflection under loading in helical spring is given by, ∆=64PR3nGd4where, P=load on…

Q: Partition A. Determine the reactions for typical interior joist in the floor framing system that…

A:

Q: Given inner diameter=1.5in, outer diameter = 1.9 in, G=11000 Ksi. Find torque that causes shear…

A: Answer We can use Torsion equation to calculate the Torque causing shear stress of 7.5 ksi at points…

Q: Problem: for the uniform beam below, A, C and D are roller supported and F is pin connected to the…

A:

Q: Problem 3 For the frame shown with the given applied load, determine the vertical reaction at roller…

A: Given:Required:Vertical reaction at roller support A

Q: Find the average of the torque in kN.m. which a shaft of 50 mm diameter can transmit safely if the…

A:

Q: The shear force diagram of a beam is shown in the figure. Draw the bending moment and load diagrams.…

A: Given data: Shear force diagram:

Q: 100 lb/ft 300 lb - 4ft 4ft *2ft>2ft 1. For the beam shown, a. Draw the FBD (Free Body Diagram). b.…

A:

Q: Situation #2 El is Constant (Assume El = 1 kN-m²) B kN/m B= 8 A= 5 A 7 m 14. Determine shear at C…

A: Given: Required: Shear at C in conjugate beam Moment at C in conjugate beam Area for moment…

Q: solve the following problem with the correct answer please, please make sure to show all work so I…

A: Step 1: Step 2: Step 3: Step 4:

Q: 50 mm -150 mm - FIG. P1.37 в с 50 mm 10° T

A: