Complete the Servo motor lesson. Look up Servo PWM Timing. The servo motor receives a PWM like control pulse as an input. You send a pulse with duration of 1 ms every 20 ms, and the servo motor understands that the desired angle is 0 deg. If you send a pulse with duration of 2 ms every 20 ms, the servo motor understands that the desired angle is 180 deg. If the desired angle is 146 degrees, what is the duration of the input pulse in micro seconds? Round it off to a whole number.

Complete the Servo motor lesson. Look up Servo PWM Timing. The servo motor receives a PWM like control pulse as an input. You send a pulse with duration of 1 ms every 20 ms, and the servo motor understands that the desired angle is 0 deg. If you send a pulse with duration of 2 ms every 20 ms, the servo motor understands that the desired angle is 180 deg. If the desired angle is 146 degrees, what is the duration of the input pulse in micro seconds? Round it off to a whole number.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain in detail the below reasons why the pulse generator will need to be replaced?
A stepper motor having a resolution of 300 steps/rev and running at 240O rpm has a pulse rate of- pps. 10,000 6000 O 4000 8000 Reversing the rotation of BLDC motor can be done by Direction can't be changed O Reversing phase sequence Reversing supply terminal Changing logic sequence
Q
If the high pulse lasts 1.725 ms, what angle does the servo motor have? 1.120.3 degrees 2.130.5 degrees 3.115.8 degrees 4.148.7 degrees 5.152.1 degrees
A 250 V series motor draws a current of 40 A. The armature resistance is O.15 Q and the field resistance is 0.05 Q. Determine the maximum efficiency of the motor 83.8 93.6 90 95.6
The DC compound motor is start by using the starter.
Draw occ at 800 rpm At 1000 rpm And 600 rpm and air gap Field Armature emf V Armature emf V Armature emf V current(A) At 800rpm At 1000rpm At 600rpm 8 10 6 0.3 28 35 21 0.5 46 57.5 34.5 1.0 94.5 118.125 70.875 1.5 143 178.75 107.25 2.0 175 218.75 131.25 2.5 195.5 244.375 146.625 3.0 211 263.75 158.25 3.5 224 263.75 168 4 234 280 175.875 4.5 243 293.125 182.625 5 252 314.375 188.625 6 266 331.875 199.125 7 277 347.5 207.375 8 286 368.125 214.5 9 295 368.125 220.875 10 302 226.5 226.5 The drawing must be handwritten without using a computer scale X-axis 1cm = 1 y-axis 1cm =20
Pre-Laboratory Assignment 1-) What are the basic purposes of using an oscilloscope and a multimeter? 2-) What is the difference between AC and DC coupling? 3-) What is the purpose of the trigger systemin the oscilloscope? 4-) Draw the following signals: a-) 5 sin 2n1000t b-) 3cos2n500t +3
7. The transformer is a 10:1 each diode drops 0.7V in the forward direction. What is the output Waveform look like? Draw max peak voltage show voltage at point A. Transformer 120V 60HZ 10ko Line Coid
Please provide Handwritten answer
What will be the full speed of a 24 pole 50 Hz polyphase synchronous machine? Express in r/min and rad/sec
If field current is not supplied internally by the armature, then the machine is said to be generator. O Shunt O Self excited O Compound O separately excited