Close Window A Moving to the next question prevents changes to this answer. Question 9 of 17 Question 9 Save Answer The figure shows the pole configuration of the open loop transfer function of a control system. The poles are located as shown. The two poles on the imaginary axis are located at + wj = 1j and -wj =-1j, and the pole on the real axis is located at -p = - 2. Find the location of the intersection point of the asymptotes with the real axis. * s-plane

Q: (i) Initial Output = %. (ii) Output after T1 Seconds = %. (iii)Output after T2 Seconds= %.

A:

Q: Problem 6: For the system shown in Figure (2), Find a. The equivalent transfer function, T (s) = C…

A:

Q: For a system shown in Fgure 3 R(s) + K C(s) s(s + 3) 1 s+ 5 Figure 3 (3a) closed-loop system. Use…

A: Given the system as shown below: a) For K=1, we need to sketch the Nyquist plot for the system and…

Q: For the open-loop pole-zero plot in the following figure (with unity feedback): R(s) with G(s)- K…

A: Given data, Open loop transfer function is given as, Gs=ks+1s+2s+3.

Q: The linear motion-control feedback transducer used by the electrohydraulic system in the Figure is…

A: A servo valve is a valve that receives pressurized hydraulic fluid from a source, usually a…

Q: 12. Design the asynchronous counter MOD 30 circuit using IC number 74LS93 (find the circuit, % duty…

A:

Q: Q6) Consider the circuit shown in figure S, assume that V Q6a) ID(on) (in mA) is A) 0.02 B) 2 C)…

A: Given the circuit, as shown below: Given Vz=8 V, RD=4 kΩ 1. We need to find ID in mA. 2. We need to…

Q: The transfer function of a phase lead controller is phase provided by this controller is (a) 90° (b)…

A: In this question we need to find a maximum value of phase provided by the given controller.

Q: Why does tthe measured time delays of the two sets of waveforms the same in Leading Power Factor?…

A:

Q: Q2 (a) Figure Q1(a) Analogue to Digital Converters (ADCs) are used to change analogue signals to…

A:

Q: Show me step by step how to do this design

A: The implementation of the logic gate using the IC in multisim software needs to be briefed.

Q: (3) A sinusoidal signal of frequency 200 Hz is sampled at a rate of 1200 samples per second. Draw…

A:

Q: G2 ပင်းကြီး H1 (င)

A: For this block diagram we need to find  a) Reduce the blocks to canonical form b) open loop transfer…

Q: Figure shows a block diagram of a process con- troi system. Determine the range of the gain K for…

A:

Q: A pressure signal from a force transducer is given as under. Analyze it in terms of harmonics,…

A: A pressure signal from a force transducer is given as…

Q: Why is the no encirclement about(-1+jo)?

A: According to question: The overall transfer function of a closed loop control system is given by…

Q: Determine the values, of K and k of the closed-loop system shown in Figure below so that the maximum…

A: values, of K and k of the closed-loop system  smaximum overshoot in unit-step response is 25% peak…

Q: An open loop system has a zero at -15 and poles at -3,-5 and -8. For a gain of 150, calculate the…

A:

Q: a) Consider the signal as shown in figure 4. -2.5 ktz 2.5 kiz Figure 4 i. Sketch the above signal…

A: