CLO 2: The girder of a simple log bridge supports a wheel load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. If the cross section of the beam is a square whose area is the same as that of the 300mm circular section, determine the maximum permissible wheel load W (in kN) based upon an allowable bending stress of 2 MPa. 850 N/m 300 mm -2.5 m- O 77.4 28.9 8.96 38.7

CLO 2: The girder of a simple log bridge supports a wheel load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. If the cross section of the beam is a square whose area is the same as that of the 300mm circular section, determine the maximum permissible wheel load W (in kN) based upon an allowable bending stress of 2 MPa. 850 N/m 300 mm -2.5 m- O 77.4 28.9 8.96 38.7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F ANALYSIS OF STRUCTURE The truss shown in the figure is loaded with forces at the joints of the truss. Compute the internal forces in the members DF, FG, FH and GH only. Indicate if the internal force is a Tension B = 200 KN 9 m 50 KN В A or a Compression. You can use Method of Joint or Method of Section. 4 m C 4 mE 4 m G 3 m 3 m 20 KN 20 KN 20 KN 20 KN
Please Solve this correctly and clearly.
The signboard truss is designed to support a horizontal wind load of 700 lb. If the resultant of this load passes through point C, calculate the forces in members BG and BF. The forces are positive if in tension, negative if in compression.Please Help Me!!
Determine the forces in members DJ and EJ of the loaded truss. The forces are positive if in tension, negative if in compression. L 2 B L L L K D I L L 6 panels at 8 m H L 72 L 7m 0.40 m 1.4 m
A= 1 B= 5 Y= 83 X= 256
For the following problems use an allowable stress equal to 25 ksi for bothtension and compression. Calculate the volume of the truss.PART A. Use the beam-truss analogy to design the following truss.PART B. Perform the structural analysis of the truss and design each member using itsactual internal force. Compare the truss volume to the one of PART A.
Answer within 5 minutes for thumbs up.
A Pratt roof truss is loaded as shown in the figure. Using the method of joints, determine the force in members CD, DE, and DF.
Solve the forces in each member in terms of force P.
D E b G H a a a + a a a P1 P2 P3 Determine the force in members FE, LE, and KL of the truss, and state if the members are in tension or compression. Type your answer as the force using three significant digits, followed by the unit and then a Tor C to indication tension of compression. P - 4 kN, P2- 5 kN, P3- 12 kN, P4 = 6 kN a- 2 m and b-3 m What is the force in FE? What is the force in LE? What is the force in KL?
Determine the forces in all bars of the truss in the Figure. If your solution is staticallyinconsistent, what conclusions can you draw about the truss? How might you modify the trussto improve its behavior? Explain.
Problem 1 The cross-sectional area of each member of the truss is 1200 mm². Calculate the stresses in members AB, BC, DF, CE, and BD. A 4 m C 100 kN B 6 m 3 m 200 kN D 4 m E 3 m F