clearance between the punch and the die should be

Q: Determine the distance s to which the 90-kg painter can climb without causing the 4-m ladder to slip…

A: Given Data Weight of the painter = mg=90(9.81)=882.9N Weight of the ladder =mg=15(9.81)=147.51N The…

Q: 11.6 Two 15-mm steel plates with S, = 400 MPa are butt-welded using E70 series weld- ing rods and…

A:

Q: 0.3 m C B 1.5 m A 2 m 0.5 m Hello, given the following diagram can you help identify the components…

A:

Q: Calculate the second thinner thin film with n = 5.4, so that there is destructive interference. The…

A: Given:- n1=5.1 n2=5.4 λ= 678  nm

Q: Estimate the resultant force of water on a quadrant gate. It's radius is 1 m and width 2m. The…

A:

Q: There is a plastic rod having a length of Lred, and a diheter of d,oa. The elastic modulus of the…

A: As per given question  Length of rod=0.22m Diameters of rod =0.014m P=350N Ep=2.7gpa Vp=0.4 We have…

Q: 5. Determine the constants 1, in order that the velocity т, and m x+lr y+mr z+ nr where r = x² + y²…

A: Given : To find : l, m, n

Q: A block of mass M= 50 kg rests on a horizontal plane as shown below in Figure- 2a. Find the…

A: Given: The mass of block, M = 50 kg The coefficient of static friction, µs = 0.25

Q: Calculate the horizontal force acting on the conical part of the pipe! $50 mm = 3.5 m' / min O 200mm…

A:

Q: Bar AB has an angular velocity AB = 9 rad/s. (Figure 1) Figure AB 200 mm 0=45° 500 mm 30⁰ 4 < 1 of 1…

A:

Q: Problem # 5 Heat Loss - Basement Walls and F loi A 20 ft x 100 ft, 7-ft deep basem ent must be w…

A: GivenDimension of basement=20ft×100ft=6m×30mdeep=7ft=2.13mTemp=68°F =20°CTo findHeat needed if…

Q: A 1450 N sphere is resting in a trough as shown in Figure. Determine the reactions developed at…

A:

Q: The hydraulic cylinder shown in the figure below, with a 3.2-in.-diameter piston, is advertised as…

A:

Q: Find the reactions for the supports on the frame below. P is 12 kN in the x direction, F is 24 kN in…

A: Given:-P=12 kNF=24 kNR= kNTo find:-Reaction on the frame

Q: The wood beam in (Figure 1) is subjected to a load of P = 15 kN. Grains of wood in the beam at point…

A:

Q: Part A pipe assembly in (Figure 1) is secured on the wall by the two brackets. If the flowerpot has…

A:

Q: The open tank shown, which has a liquid with a specific gravity of S-2.0 as shown in the give…

A:

Q: Electrical strain gauges were applied to a notched specimen to determine the stresses in the notch.…

A:

Q: The cords ABC & BD can each support a maximum load of 274 lb. D. 1213 What is the maximum weight of…

A:

Q: 300 mm 300 mm At the instant shown, 8 = 03 rad, and rod AB is subjected to a deceleration of a=10…

A:

Q: Determine the tension needed in cables AB, BC, and CD to support the 12-kg and 15-kg traffic lights…

A:

Q: Given that both loads P have a magnitude of 31 N, Determine the forces in the ALL the members with…

A:

Q: Calculate the centroid for the shaded portion of the figure as shown. Take a = 115 mm, b=55 mm, c =…

A:

Q: The roof over a 9.0-m x 10.0-m room in a school has a total mass of 12900 kg. The roof is to be…

A:

Q: Determine the tensions in cables AB, AC, and AD. 1.70 m 2.10 m 1.20 m 0.65 m 2.9 135 kg Answers: TAB…

A: Given data: m=135 kg Need to determine the tensions in the cables AB, AC and AD.

Q: 1. Calculate and plot the first three mode shapes of a free-free bar. k р, А, I m Figure P6.21 Beam…

A:

Q: Take that w1 120 N/m and w2 = 180 N/m. W1 B, -6 m - 5 m Ľ. W2 Part A Replace the distributed loading…

A:

Q: F3-28. Replace the loading system by an equivalent resultant force and couple moment acting at point…

A:

Q: please solve this quick

A: GivenF=500Na=26cmb=32cm

Q: A uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 3.5 kg, a length…

A:

Q: The first steam power plant operates on an ideal reheat Rankine cycle. Steam enters the first…

A:

Q: How long does it take the bob to make one full revolution (one complete trip around the circle)?…

A: Given:Bob diagramBob with mass mTo find:Time it takes to make one full rotation

Q: Find the Area Moment of Inertia about an x axis passing through the centroid (Ix) of the composite…

A:

Q: B/34 Determine the moment of inertia about the x-axis of the portion of the homogeneous sphere…

A: It is known that the moment of inertia of a solid sphere is Here, Ro is the radius of the sphere.…

Q: PROBLEM # 1:- Answer the following questions in the given space 1 What are the three elementary…

A: given; (1) what are the three elementary parts of a vibratory system? (2) define the number of…

Q: Problem 2 Determine the total time t (in hrs.) required to fil the spherical tank with liquid whose…

A: Given:s=2.50m=400 Kg/mind=4 m

Q: A solid cylinder with a radius of 3.9 cm has the same mass as a solid sphere of radius R Part A If…

A:

Q: A 1480-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the…

A:

Q: The figure consists of four forces. a. If F3 = 20 kN and 0 = 15°, determine the magnitude and…

A: As per given question  F1=50 KN F2=30KN F3=20KN F4=25 KN WE have to determine magnitude and…

Q: Air at 8 MPa and 3500C is contained in a well-insulated cylinder covered by a weighted piston, which…

A:

Q: turning moment on the crank

A: Given data; A slider crank mechanism with ,crank radius, r=200 mm=0.2 mConnceting length ,l=800…

Q: Consider a fully reversible cycle consisting of isentropic compression, isothermal heat addition,…

A:

Q: ergoes a process in whicl same time interval, 220 J ot it

A:

Q: Study the water tank illustrated in Figure 1 below and calculate the horizontal distance (x) the…

A: Given:Height of water level in the tank, H=3 mHeight of th water poening, h=180 cm

Q: Consider the beam's cross-sectional area shown in (Figure 1). Suppose that a =3 in., b= 10 in., and…

A:

Q: A copper specimen of Young's Modulus 129 GPa is subjected to a tensile test in a laboratory and the…

A: Given data :-   Young's Modulus 129 GPa  a) Initial length of the Specimen = 396 mm; b) Initial…