A Click Submit to complete this assessment.Question 6 of 6stion 6Save AnswerThe power input to a 306V, 3 , 50 Hz induction motor is 19.9KW at Sslip. If the input p.f. is 0.75 lagging, friction and windage losses are 1,289 W and stator losses are 1,226 W. Find the value of line current.

Answered: Image /qna-images/answer/463f8254-eda0-4ec1-a724-1593c50739c2.jpg

ck Submit to complete this assessment Question 6 of 6 Save Answer wer input to a 306V, 3. 50 Hz induction motor is 19.9KW at 5slip. If the input p.f. is 0.75 lagging friction and windage losses are 1,289 W and stator losses are 1,226 W. Find the value of line current.

ck Submit to complete this assessment Question 6 of 6 Save Answer wer input to a 306V, 3. 50 Hz induction motor is 19.9KW at 5slip. If the input p.f. is 0.75 lagging friction and windage losses are 1,289 W and stator losses are 1,226 W. Find the value of line current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

H.W 1) A 4-pole, 500 V d.c. shunt motor has 720 wave-connected conductors on its armature. The full-load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 Q and the contact drop is 1 V per brush. Calculate the full-load speed of the motor. H.W 2) A d.c. series motor with series field, and armature resistance of 0.06 ohm and 0.04 ohm respectively is connected across 220 V mains. The armature takes 40 A, and its speed is 900 rpm. Determine its speed when the armature takes 75 A, and excitation is increased by 15% due to saturation.
Final 1A DC shunt motor is rated 10HP, 250V and is connected to 235V source. The armature resistance is 0.2 ohm, the field circuit resistance is 125 ohm and the total rotational losses are 380W. The motor is driving a load, and it draws an armature current of 30A, Calculate the output power. b) 41 d) 6490 6870 7492 7460 Boş birak
Q2] Fill in the blank (9 Marks) 1-The current drwan by the armature of D.C. motor is directly proportional to 2- The speed of a D.C. shunt-wound motor will shunt field regulator is increased. 3- The synchronous speed of a three-phase induction motor is number of pairs of poles. Rotor copper losses Rotor input power in induction motor = 5- A 4-pole three-phase induction motor has a synchronous speed of 25 r.p.s. The frequency of the supply to the stator is_ Hz. 6- The power input to a mains transformer is 200VA. If the primary current is 2.5A, the secondary voltage is 2V and assuming no losses in the transformer, the turns ratio step down. is 7- A 200kVA transformer has an iron loss of 1 kW and full load cu loss of 2 kW. Its load kVA corresponding to maximum efficiency is kVA. 8- If cu loss of a transformer at 7/8th full load is 4900 W, then its full-load cu loss would be watt. 4- if the value of resistance of the proportional to the 9- The slight curvature at the lower end of the open…
A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be
A 240 V, 60 Hz, Delta connected, 870 r.p.m., Eight poles, Three-Phase Induction Motor has the following per phase parameters: R1 = 0.07, R2 = 0.05, X1 = X2 = 0.2, Xm = 6.5, Draw the approximate equivalent circuit and determine the following: I. Starting Torque Maximum Torque II. I. Rated Torque IV. Stator Current V. Power Factor VI. Input Power VII. Rotor Current VIII. Magnetizing Current IX. Stator copper loss Х. Rotor copper loss