O 10.932 ft/sec O 12.735 ft/sec O 14.524 ft/sec O 16.042 ft/sec O 18.843 ft/sec The saddle of a swing is 3 feet from the ground. Peter plays on a swing and acquires a vertical displacement of 4.857 feet with respect to the level ground. What is the velocity of Peter when the saddle of the swing is 3 feet from the ground?

O 10.932 ft/sec O 12.735 ft/sec O 14.524 ft/sec O 16.042 ft/sec O 18.843 ft/sec The saddle of a swing is 3 feet from the ground. Peter plays on a swing and acquires a vertical displacement of 4.857 feet with respect to the level ground. What is the velocity of Peter when the saddle of the swing is 3 feet from the ground?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. For this series of 4 questions, two blocks, A and B, are connected using the cable and pulley system as shown. (The cable and pulley system is friction-less and weight- less.) The coefficient of kinetic friction between block A and the inclined plane is k = 0. 2. Initially the blocks are moving but eventually come to stop. You will be asked to solve for different things. Please pay attention: the numbers may change from problem to problem since they are randomized. 2) If at an instant block A moves down the plane at a velocity of 7.8 ft/s, determine the velocity of block B at this instant. Your answer must include 1 place after the decimal point and the proper unit. The velocity is positive if block B moves upwards. A Your Answer: Answer B units C D
This is the 3rd time I am giving the same questions. Which method is corect ? Method 1 or 2 ? Frist time I got answers from you as method 1. The second time your answers were haisy. You gave answers by method 2 as Ra= 12 kn and Rb=28kn but posted SFD and BMD on the basis of method 1 ? Please clarfy the answers.
This subject is Highway and Railroad Engineering. Please help me, Ill upvote this :) Thankyou for your help :)
Instruction: Solve the following problem/s and show your complete solution for each. Input your final answers on the online Form in the link. Variables (a, b, c, d, and e) can be found on the list on page. You must upload your plate on the last part of the online Form. Problem 1. Use slope-deflection method and determine the following unknowns on the beam shown below. Assume El is constant. Show complete and organized solution. Round-off your answers to two decimal places. In the Form input your answer to the following questions. a. Fixed-end moment (FEM) on joint B of member AB in kN-m. Indicate negative sign if counter- clockwise. FEMBA b. Fixed-end moment (FEM) on joint B of member BC in kN-m. Indicate negative sign if counter- clockwise. FEMac c. Moment at joint A in kN-m. Indicate negative sign if counter-clockwise. MAa d. Moment at joint B of member BC in kN-m. Indicate negative sign if counter-clockwise. Mac e. Vertical reaction at roller B in kN. R. "0.7a" m "0.7a" m A(m)=3.70…
Give me two (2) example with complete solution of Linear Regression.
Introduction Structural analysis is important for designing all type of structure including truss structure. There are several method to analyse truss structure. Therefore, student should be able to analyse the truss structure with appropriate method. This assignment is given to student to evaluate the ability of the student in solving the complex problem involving truss structure as shown in Figure 1 below. B 6m 88) O 20kN By using an appropriate method, i) 6m 20kN/m D 30KN Figure 1 6m H 20KN 6m LL G Figure 1 above shows a truss structure, which is supported at A and G. The truss is design to support a uniform load 20kN/m from C to E as shown in the figure. Given the elastic modulus, E=200GPa, and the cross-sectional area for member AJ, JI, IH, and HG is equal to 500mm² while other members is equal to 250mm². Based on the details given, solve the following task to analyse the truss structure. Task 1 8m Describe the determinacy and stability of the truss structure. Your answer must be…
Q₁: Circle the most correct answer (or answers) for each of the followings: 1- The time required by rain water to reach the outlet of drainage basin, is generally called (A) Time of concentration (C) Concentration time of overland flow 2- Pick up the correct statement from the following: (A) The specified duration of unit hydrograph, is called unit duration (B) The rain during specified duration, is called unit storm (C) The number of unit hydrographs for a given basin, is theoretically infinite (D) All the above 3- The below figure. If the value of Fi index is 3 cm/hour, the runoff will be: Rainfall in cm 10 Times in minutes (B) 3 cm (C) 4 cm (B) Time of overland flow (D) Duration of the rainfall (A) 2 cm 4- A hyctograph is a graphical representation of (A) Rainfall intensity and time (C) Discharge and time (D) 5 cm (B) Rainfall depth and time (D) Cumulative rainfall and time 5. Pick up the correct statement from the following: (A) Hydrograph is a plot of discharge and time 6-…
I need the answer as soon as possible
With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 4 answers is correct
estimate standard deviation:
ESSAY. List down or enumerate what are asked for in each number. 1. What are the do's and don'ts in sampling distribution? 2. Difference between prediction and tolerance interval. 3. Differentiate null and alternative hypothesis. 4. Difference of simple linear regression from correlation 5. Difference of CRD and RCBD
With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 4 answers is correct