(3) 4" 4 11 4" 20" Uncracked, (1) ftop = ? (2) f bottom=? ft-k M= 30f

Q: There is a statically indeterminate beam in which the horizontal force at the left and right ends…

A:

Q: Find fr (modulous of rupture) = ? M, bending moment = ? k = ? j = ? y = ? I = ? 0

A:

Q: There is a sta at the left and force is show The flexural s

A: Ds = De + Di = 5-2-1 = 2                         it is indeterminate with 2 but RA & RB given…

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A:

Q: Ah G Av E 60° 49 30 Bh B x F x D x •METHOD OF JOINTS 20 N Tabulation of forces from Method of…

A:

Q: Point A is located at coordinates (2.5, 1.5, -10) Point B is located at coordinates (2, 1,-5) Point…

A: Answer  We know that the increase in stress under a corner point of rectangle is given by  ∆σz =…

Q: Engr 309. 7/7/22. Name_ the stresses at the POI. bott 3m 2m 4m 0.36 kN -8KN m вя POI th 2m2m 74,36…

A:

Q: The thin rectangular plate shown is uniformly deformed such that ɛx = +864 µɛ, ɛy = -510 µɛ, and yy…

A: This is the problem involving strain transformation. The angle made by BD with horizontal is to be…

Q: three locations that could exceed allowed stresses and how to find principle stresses using Mohrs…

A: Three location that could exceed allowed stresses are:- (a) At the junction of flange and web both…

Q: 2.4 25 kN/m 15 kN/m E Hinge A 11 -10 m Hinge Ray = 170.25 KN Rax = 309.25 KON Ma = 11128-50 KN-M 15…

A: Free body diagram: The angles; θ=tan-1103=73.3 Conver the UDL to point load: Slant…

Q: Engr 309 8/4/22 Name. 3' Jook て 31° 54.3° C A 2' 5' B Determine buckling. Fill in the blanks. BC [..…

A: The truss with the load and support conditions is given asThe cross section of member AC and BC is…

Q: Example 10.1: - SP and Resistivity (shallow and deep) logs are shown in Figure 10.1 in front of…

A: Sandstone is generally a rock making generally of minerals are created from sand. The stone gains…

Q: 1-54* Three forces are applied along the centerline of a steel bar as shown in Fig. P1-54. Determine…

A:

Q: The lumped section shown has an internal shear force of 3000 lb. All lumped areas are 0.5 in² and…

A: internal shear force=3000lblumped area=0.5in2web thickness=0.050"

Q: Probl A submerged rectangular gate holds back water. Gate is 2 m. wide. Compute force (F=?) to open…

A: Given a submerged rectangular gate holding water, it is required to determine the force (F), to open…

Q: Design Span = 6m Design Pressure fe' fy CC a = simply supported solid one-way slab. vism = 8kN/m² =…

A: Answer  One way slabs are designed as rectangle beam having large width to depth ratio. We need to…

Q: H Y G 30 kips - 20 30 kips C 40 kips 40 kips 40 kips 50 kips 70 kips

A:

Q: (structural analysis) Calculate and draw: FBD, NFD, SFD and BMD.

A:

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.