2- Determine the force in member BD and the components of the reaction at C and D. 240 NUM 150mmy 41111111111 Have 200MM 450mm 8000 B * Slomm X

Q: 2) The system given below is composed of two parts. AB part is a beam and the other part is a planar…

A: The FBD of the structure is shown below:

Q: fined the weight of the pully te Kep the system in equilibrium 65N 260

A: Given data  Point load Pulley Slope. We will use force balance equation to solve this problem.

Q: weight of the pully teKeep the system în brinme aquilibe Sindd the

A:

Q: A B с 4m D 4m 4m 187,5 202,5 197,5 A 192,5 B -6m D C -6m Calculate the magnitude of the force acting…

A:

Q: Determine the slope at B and the displacement at poust for for the beam IDm 10m 10m (0m

A:

Q: For the frame loaded as shown, draw the complete and correct FBDs of the following: whole frame,…

A:

Q: Determine the horizontal and vertical components wich the pins exert on member EDC of the frame

A: Determine the horizontal and vertical components wich the pins exert on member EDC of the frame ?

Q: 250 mm 60 350 mm The pin at point O in the figure below The load it can safely carry is 5 kN. In…

A: To find  Value of L and reaction at B?

Q: 12K A 81 81 84 8K 6k 8K

A: Introduction: For solving reactions acting on any structure we have to follow three equilibrium…

Q: Member Magnitude,N X- Y- component Component 0.6 m A 500 N В AE 2000 N 0.3 m O F A 0.2 m 0.4 m 0.3 m

A:

Q: 4 Which of the following gives the reaction at D in the given beam? 300N₁ 210 N/mp 100 Nm TIT777 5m…

A:

Q: y | 1 A -X 25' 15⁰ 40° C F = 13 kips 15' B 11 .n

A:

Q: 1. Resolve the couple-force system into a single resultant force and a single resultant moment at A.…

A:

Q: Determine the reactions of the structure, given that X= 7 ft. 10 kips F ———X—₁▬▬▬▬▬▬5²- The…

A: Given data:- X = 7 ft.

Q: Replace the force system acting on the frame by an equivalent resultant force and couple moment…

A: Equilibrium of horizontal forces, Equilibrium of vertical forces,

Q: Which of the following gives the reaction at E in the given beam??

A: We know that at internal hinge we get zero bending Moment. And reactions at hinge will get…

Q: 4KN 4KN 4KN 2KN 30 6m 309 6m 6m SKN 8KN Figure 5 (#10-#12) os. 10 -12: Refer to figure 5. _10. What…

A:

Q: The value of M in the beam ABC shown in the figure is such that the joint B does not rotate 30 kN/m…

A:

Q: Problem 7.5 - Determine the reactions at supports A and C. Şımēệmm Emm A ---- 2 kN V 40° Emm B Ö 60°…

A: Given data:-

Q: Sined the weight of the pully te Kep the system in aquilibrinme 65N 60 om

A:

Q: find all reaction for the frame by the force method

A: Let's take Hc as redundant  Using Theorem of least work (Force Method)

Q: For what value M of the clockwise couple will the horizontal component of the pin reaction at C be…

A:

Q: find the reaction of the beam show all the work

A: ∑MA=012×16×10×5 - RB×10=0RB=40 k ↑

Q: Since the beam is cantilever please solve the reactions at B only being fixed at that point. 60 KN/m…

A:

Q: Determine the following reactions and the value of P

A: Given Data  Determine the support reaction and the value of P.

Q: Solve for Ray and Rby

A:

Q: The member is supported by a square rod which fits loosely through the smooth square hole of the…

A: First, we draw the free body diagram:-

Q: b) Determine the reaction forces and/or reaction moments at pin (You can neglect the height of the…

A:

Q: Where will be the line of action of the force F? O it will pass through the centroid of the gate…

A: Option 3 is correct  It will pass through the centre of pressure on the gate or ycp .

Q: 4 col lok 1. W

A: Solution:- Given data:- It as asked to solve external support reactions for given beam.

Q: Find the reactions at A and B

A: Step 1: Step 2:

Q: 20N Y Determine the 50N Reactions ot point A ? A

A: To determine: Reactions at Point A.

Q: A key is used to turn an axle. A pin fits into hole A and a flat, frictionless surface rests at…

A:

Q: indicated operation: (5+2i)+(7+4i)

A: Solution: (5+2i)+(7+4i) 5 + 7 = 12  (real part) 2i + 4i = 6i   (imaginary part) Thus,  Ans: 12 + 6i…

Q: 1. Determine the moment about the point R* 50 N ↑ R (-3,3) T (4,3) S (6,-3). O Nm 350 Nm O 100 Nm O…

A:

Q: of 3x+ 2000lb aft FR₂

A:

Q: 2/ The lattice structore Shown in the fiqure is subject to the influence of three external for ces.…

A:

Q: Determine the reaction in the support of the beam loaded and supported as shown: 5 kN/m A 10 m B 5…

A:

Q: oirt B. as showm a following ignty the slope-deflection method. Sk 5 k/t S ft 8 t

A:

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.