Determine the centroidal moment of inertia. * 100mm x 50mm x 10mm C250 x 30 C250 x 45

Q: 10.1 A simply supported steel column is 8 ft long and has a square cross section of side length b.…

A: using eulers equationPcr=π2EIL2Pcr=π2Eb412L2b4=12PcrL2π2E

Q: The acceleration of a particle traveling along a straight line is a = -si m/s?, where s is in…

A: Answer We are given acceleration of the particle a = 14s12   m/s2 Given condition  If v=0, s=3.2 m…

Q: For an actual ship that is required to sail at a speed of 12 m/s, a 1:50 scale model is prepared and…

A:

Q: 1. Two platoons of cars are timed over a distance of 0.7 km. Their flows are recorded. The first…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: An experimental device imparts a force of magnitude F = 48 lb to the front edge of the rim at A to…

A:

Q: 4. A canal is cut into a soil with a stratigraphy shown in the figure below. A flow takes place…

A: Given data in question  Layers depth and permeability  To find out  Physical meaning of permeability…

Q: Determine the force in members GF, FB, and BC of the Fink truss and state if the members are in…

A: A truss hinged at A and roller supported at D. Vertical forces 800 lb, 600 lb, and 800 lb act on G,…

Q: Problem: A 2 story bank is constructed with reinforced masonry walls and the floor and structural…

A: A "2-story bank" is a building that houses a bank and has two stories or levels and the bank has two…

Q: c. Using water reducer, how can we improve workability without changing the compressive strength?…

A: Given data,

Q: Test Data and result Sample # Age (days) R (mm) Area (mm^2) Q(N) о (MPa) 1 7 100 400000 7 100 410000…

A: Compressive strength is defined as the ratio of the compressive force applied per unit surface area…

Q: Determine the reaction force in KN on the other end of the gate (it is found at 3 meters from the…

A: The depth of gate, H=2mThe width of gate, B=2mThe depth of submergence, h =3m

Q: 1. Draw the Shear and Moment diagrams and determine the maximum shear and maximum Moment. A 7KN-M 20…

A:

Q: What is the difference in elevation between station 3+900 and 5+200? (Ans.) What is the difference…

A:

Q: Properly illustrate the shear and moment diagrams for the given beam. Compute the shear reactions…

A:

Q: A torque of magnitude T = 1000 N·m is applied at D as shown. Shaft AB and CD have an elliptical…

A:

Q: . A simply supported beam having a span of 10m carries a uniform load of 20 over its entire length…

A:

Q: A 100-meter steel tape is 5 mm too short at 21°C with a pull of 8 kg. A rectangle is measured with…

A: Given: Measured length of rectangle (L)=200.75 m Measured width of rectangle (B)=100.50 m…

Q: A system of force is shown in FIG 2. Which of the following gives the nearest resultant of the…

A: To find resultant, it's direction and distance from point A

Q: ∆у = ду 5WL3 384Е (5 ×3758.0698kg x33m3) (384 X200GPa x39.2x106 mm4

A:

Q: (Given E = 73 Gpa, v = 0.33.) (1) What the normal strains and by using Mohr Circle method: - (ii)…

A:

Q: A load of 2000 kg is placed on a vertical steel beam 5 m high whose cross sectional area is 30 cm.…

A:

Q: fast answer thx

A: From Pythagoras theorem, (Hypotenuse)²= (side 1)²+(side 2)² Given, Hypotenuse= 10ft Side 1= 9ft

Q: A Motel with toilet, bath and kitchen facilities is to serve a maximum of 300 persons. Determine the…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 8. An empty warehouse room, 12 meters long, 8 meters wide and 4 meters high is at room temperature.…

A: Density = mass / volume    specific weight = weight / volume

Q: Describe the purpose of soil stabilization and discuss at east three methods of chieving soil…

A: As per guidelines one need to answer only first question.

Q: A cantilever beam, 70 mm wide by 230 mm high and 8 m long.arries a load that varies uniformly from…

A:

Q: If M-50 kN-m, what is the maximum bending stress about the z-axis? (in O MPa)

A: To calculate the maximum bending stress for a given cross-section with given moment.   Given data,…

Q: 1. Solve the axial forces of the members indicated in the box below. 50 KN 75 KN 25 KN 3.00 m 3.00 m…

A:

Q: SITUATION. Refer to the figure. B C a b V = 10.5 V = 0.5 V = -11.5 The shear diagram due to loads on…

A: Find  1. Maximum span moment  2. Concentrated point load at C

Q: What is the unit cost Php/sq meter of a 50m by 2m 4" CHB wall if you are to include the cost of…

A: Given data The dimensions of the 4 inches CHB wall is 50 m * 2 m The vertical spacing is 60 cm for…

Q: A 50 mm diameter siphon discharges water from a reservoir (Point 1 elev = 20m) into open air (Point…

A: To find :- Velocity in the siphon in m/s

Q: 3. What would be the magnitude of forces P and Q that would maintain the shape of the cable as shown…

A:

Q: A soil profile is shown in Figure 1. Determine the total consolidation settlement of the clay layer…

A: ∆σ = 15KPa

Q: 16. For a gage reading of -17.1 kPa, determine the (a) elevation of the liquids in the open…

A: the gage reading (P) = -17.1 KpaTo Find: -A) the elevation of the liquid in the open pipe piezometer…

Q: PROBLEM 2 For the beam shown below, determine the following 1. Reactions 2. Maximum Shear 3. Maximum…

A: GIven : Beam with UVL, UDL and point load Static Indeterminacy = 4-2 = 2 We will use matrix method.…

Q: What is the equivalent wrench of the force couple system acting at point O, given the F = 400 N and…

A: To determine equivalent force couple system.

Q: For the given beam, draw the simplified free-body diagram and below it the shear and bending moment…

A:

Q: 2) The aggregate used in road construction begins degrading integrity of said roadway when pieces…

A: Given: Mean of aggregate used = 19 mm Standard deviation = 5.5 mm The percent of usable load when…