Determine the safe uniform live load that the beam can carry on a simple span of "L" meters with the ff. parameters: Given: width of beam, b = 250 mm depth of the beam, h = 560 mm clear cover up to center of bars = 65 mm Diameter of bar = 28 mm No. of tension bars = f'c = 28 MPa fy = 414 MPa SDL (excluding beam wt) 8 kN/m Span of beam, L = 8 m

Determine the safe uniform live load that the beam can carry on a simple span of "L" meters with the ff. parameters: Given: width of beam, b = 250 mm depth of the beam, h = 560 mm clear cover up to center of bars = 65 mm Diameter of bar = 28 mm No. of tension bars = f'c = 28 MPa fy = 414 MPa SDL (excluding beam wt) 8 kN/m Span of beam, L = 8 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude of the resultang.
Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties of fc' = 21MPa, fs = 140MPa, n = 7, 50mm effective cover, determine the following: Note: Assume the beam has cracked. 650 50 500 ܘܘܘ 200 150 150 What is the flexural capacity of the beam Express your answer in KN-m.
Use F = 50 ksi and select a shape for a typical floor beam AB. Assume that the floor slab provides continuous lateral support. The maximum permissible live load deflec- tion is L/180. The service dead loads consist of a 5-inch-thick reinforced-concrete floor slab (normal weight concrete), a partition load of 20 psf, and 10 psf to account for a suspended ceiling and mechanical equipment. The service live load is 65 psf. a. Use LRFD. -4 @ 6' = 24- 30′ a. W16X31 b. W16X45 c. W16X26 d. W16X77 e. W16X57 H -H
Please answer asap with four decimal places
Design a continuous beam using the given data:. Data: fc' = 25 MPa Main Bars = 25mm fy = 276 MPa Stirrups = 12mm Pu = 25 kN WLL = 15 kN/m Wo 20 kN/m B 3m C 2m 4m 3m D.
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
Problem 2 A loaded cantilever beam is shown. E=29,000 ksi. The W16 section that will limit the total load deflection at the free end of the beam, B to 0.75 in. is most nearly: WD = 0.5 k/ft WL = 1.0 k/ft PD= 2 k B PL = 4 k Answer: W16 x L = 12 ft %3D
Answer should be on the choices. Please provide a NEAT or CLEAN SOLUTION. Hoping for a written solution. thanks
Please answer asap with four decimal places
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 106 mm*). For the loading shown, determine the beam deflection vc at point C. Assume P = 56 kN, w = 22 kN/m, Lag = Lsc= 2.9 m, Lco = 2.9 m. LAB LBC LCD Answer: Vc= mm.
Please explain all options..
Plz, solve this problem using Flexibility method and show all the steps one by one and draw SFD and BMD Structural Analysis-2