CITE SOME OF THE REQUIREMENTS TO FEED THIS GENERATED ELECTRICITY TO THE TRANSMISSION LINES.

Q: 9.24 A three-phase, 60-Hz transmission line is completely transposed. The separation distances…

A:

Q: Q3: A single circuit three-phase transmission line is composed of four ACSR conductors per phase…

A:

Q: The three conductors a,b,c of a 3 phase are arranged in a horizontal plane with Dab=2m, Dbc=2.5m.…

A:

Q: Explain relationship between microstrip transmission line and characteristic impedance?

A: High-frequency signals, usually in the range of a few GHz to several tens of GHz, are transmitted…

Q: A 300 km transmission line with a VR% of 95% and efficiency of 90% is operating with 230 kV voltage…

A: Given:Percentage voltage regulation, VR% = 95%Efficiency = 90%Voltage (V) = 230 kVLoad (P) = 300…

Q: Problem 6- A Three-phase 60 Hz transmission line has its conductors arranged in a triangular…

A: we need to find GMD and radius of conductor to calculate the required parameters.

Q: 1- Combined power stations may be more effective considering the economic and environmental…

A:

Q: vii. RCC poles... R... .C... . used to support transmission tower ix. Calculate charring current per…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: The separately-excited generator provides its own ______________ from the generated output voltage.

A:

Q: phasor diagram, the  line drop phasor due to resistance is in phase

A: In this question , we have to find out that in medium transmission line T configuration phasor…

Q: at 50 Hz. The diameter of each 7.8 A two-conductor, single-phase line operates conductor is 2 cm and…

A: Given data Distance between two conductors; D=3 m Diameter of each conductor; d= 2 cm To find out We…

Q: 10 mm 5 m 30 mm 6 m

A: In this question we need to find phase capacitance of the given transmission line.

Q: Discuss the significance of power factor in an AC power system. How does power factor correction…

A: The power factor is a critical parameter in power distribution systems that measures the efficiency…

Q: negligible only if the length of the Transmission Line does not exceed how many kilometers? A. 240…

A: In this question, we will write shunt capacitance effect...

Q: Q#5. Illustrate the variation of output power taken from the wind turbine? How the frequency in wind…

A: In the case of the Wind turbine generated power will vary with the wind flow. So the power will…

Q: A Parallel wire line has its radius of the conductor is 0.4 mm and the distance between the…

A:

Q: Q5 (Large Single Phase Resistive load connected to 3 phase supply) Single Phase Resistive Load eg…

A: Given  A large single phase load of Resistance = 0.25 ohm is to be connected to a three phase…

Q: A generating station has a maximum demand of 25,000 kW. Calculate the cost per unit generatedfrom…

A: Maximum demand=25000 kW Capital cost = P 120M Annual load factor = 45% Annual cost of fuel and oil =…

Q: An AC current is given by i(t) = 200sinπt. It will achieve a value of 100 after _____ sec

A: This question belongs to circuit theory . It is based on the concept of sinusoidal analysis in…

Q: The phase angle between magnetizing component current and core loss component current is 90° Select…

A:

Q: 1. Discuss the influence of the bypass, coupling, internal, and stray capacitances on the frequency…

A:

Q: Derive an expression for sag in a transmission line of equal hight poles.

A: Given: The poles are of equal height.

Q: The energy loss due to dielectric losses of a 15 kV cable is given as 1MWh. The capacity value of…

A: Given values are -

Q: -Derive and analyse relation of capacitance for 3- core cables [CLO-2,

A: Capacitance of 3 core cables: Let Cc be the capacitance between 2 cores and Ce between core and…

Q: What do you understand by impedance matching? Also write the formula of characteristic impedance for…

A: For maximum power transfer in transmission line, impedance of transmission line is equal to surge…

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.