Chose the correct answer 1- The Unit measurement of suspended solids is ...A- kg 2- The Unit measurement of Turbidity is A- °C is C- mg/L C-K D- none of above D- none of above A-mg/L D- none of above C- g/m³ B- p.p.m D- none of above A-m/sec B- m³/sec C- mg/L A-Chromium B- Mercury C- Calcium D- none of above B- 10 mm C-108 mm D- none of above 7- Public standards of Hardness in drinking water is A-500 mg/L B-50 mg/L C-100 mg/L D- none of above 8- Alkalinity species includes are A-HCO3 B-CO3 C- OH D-All of above .. 9- Dental cavities in children can prevented when Drinking water has Fluoride concentration of A- 0.1 mg/L B-1 mg/L C- 10 mg/L D- none of above 10- Toxic metals are metals that harmful to humans even when exists in concentration of .. A-Small B-Large C-zero D- none of above www B-m B-NTU 3- The Unit measurement of pH 4- The Unit measurement of alkalinity is .. 5-Non toxic metals includes 6-Dissolved materials size is lees than A- 104 mm

Q: what is the formula used in the -δp + δt = -δp + δt = -δp + δt part at the top? what is the…

A: Given:  (-δp + δt)A = (-δp + δt)B = (-δp + δt)C Required: To explain the  δp and δt meaning in the…

Q: A volume of one cubic meter of water is subjected to a pressure increase of 14 MPa. a.) Compute the…

A:

Q: A commercial laundry is considering constructing an ion exchange process to remove hardness from the…

A: The given data is: Qrequired=1000 m3/day Calcium, as CaCO3=200 mg/l Magnesium, as CaCO3=100 mg/l

Q: A liquid compressed in a cylinder has a volume of 1000 cm' at IMN/m and a volume of 995 cm' at 2…

A:

Q: Problem 2-- For a temperature rise of 100 degrees Fahrenheit and 10,000 pounds force shown,…

A:

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: Sieve size (mm) 10 5 2.36 1.18 0.6 0.3 0.15 0.075 Wt. retained (g) 0 7 30 33 62 98 55 18 Retained…

A:

Q: Find the optimum binder content for the results of Marshall test bellow and determine the properties…

A: Approach to solving the question: To find the optimum binder content and the properties of the…

Q: After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of…

A: Depth upto which SAE oil is filled in a glass to make it float on water = d , Specific Gravity og…

Q: 3. Determine the normal force between the crate and the surface 4. Determine the force P needed to…

A: Given- W = 856 N Frictional coefficient - μs = 0.3 height of block = h = 2 m Width of block = b = 1…

Q: A 10 il load is uniformly cated by an aluminum alloy pipe with an outside diameter of 10 cm and…

A:

Q: What loads are exerted on the ends of the tube, and what are the resultant stresses?

A: Length of the aluminum tubing L = 13 in Modulus of elasticity E =  Coefficient of thermal expansion…

Q: Ca+2 = 36.8mg/L Mg+2 = 2.9mg/L HCO3 = 98mg/L pH = 7.53 Temp = 9C Calculate the following: a.…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: The acrylic plastic rod is 200 mm long and 25 mm in diameter. Part A If an axial load P of 450 N is…

A: The formula of longitudinal strain is given by,

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.