Choose the schematic diagram for a conventional hardwired circuit that will perform the following circuit functions using two break-make pushbuttons: • Turn on light L1 when pushbutton PB1 is pressed. . Turn on light L2 when pushbutton PB2 is pressed. • Electrically interlock the pushbuttons so that L1 and L2 cannot both be turned on at the same time.

Q: Sketch the electronic symbol (schematic) for the following components/ devices. Briefly describe the…

A: As per the policy we can solve only 3 sub-parts of the question, please re-upload the remaining…

Q: There are three 15,000-ohm resistors connected in series across a 120-volt DC source.  What is the…

A: The solution can be achieved as follows.

Q: The fuse in the following circuit disconnects if the current exceeds 5A. (The internal resistance of…

A: Fuse  The Fuse is an electrical safety device that operates to provide protection against…

Q: A technician wants to energize a 24 volt motor, but lacks a 24 volt battery to do it with. Instead,…

A: Solution !! This is perhaps the most direct solution (setting each power supply to output 12 volts):

Q: Explain the following:  Voltage clamp method

A: Need to explain voltage clamp method

Q: what are three safety items to consider when using a voltage tester on energized circuits

A: Measuring live voltage in energized circuit can cause severe hazard to equipment and users if…

Q: The Voltage between the contacts during the arcing period is Land is just sufficient to_ O a. Very…

A: Vacuum circuit breaker.  Vacuum circuit breaker has minimum gap between fix and moving contact.

Q: What is the purpose of shunt resistors in an ammeter? A. To shorten the range of the ammeter. B.…

A:

Q: An ammeter of resistance 4800 with shunt resistance 2002 is connected in series with a reasistance…

A: It is given that:Ammeter resistance is Shunt resistance is Series resistance is

Q: Consider a system with four pushbuttons and three lamps and three motors. PB 1 is used for main…

A: Solution- Given, Consider a system with four pushbuttons and three lamps and three motors. 1. PB 1…

Q: g Technology- Toronto CHAPTER 7: SOLDERING TECHNIOUES ES 7.5 QUESTIONS Which tools will you need for…

A: Note: According to bartleby guidelines, we have to answer only first question. 1) Soldering is the…

Q: the

A: Let us assume initially A, B & C are zero.

Q: To operate a system that will draw high current, this type of integrated would you use it, why?…

A:

Q: What is lightning? Describe the mechanism of the lightning discharge.

A: Lightning- It is a discharge of electrical energy of very short duration and high voltage between a…

Q: What is the negative effect of operation a contactor coil above or below it's rated voltage

A: The contactor operational limit is 85 to 110 percent of the rated coil voltage.   The percent…

Q: How would you design a fuse protection system? Choose the right answer with justification: a)…

A: We need to answer how efficiently we can design a fuse protection system for PLC's.

Q: 30) A specification requires the PV array for a stand-alone PV system to be sized to produce 1.25…

A:

Q: What percent of the full-load current will be attained after one time constant?

A: Let's consider the load as R-L load because most of the loads are inductive in nature and initially…

Q: What is the condition of a one-way switch if it has no resistance between terminals at both toggle…

A: As per Bartleby's guidelines, we are allowed to solve only one question, please ask the rest of the…

Q: parte A • Develop and explain the electrical schematic for the excitation coil in series. • Develop…

A: It is asked to develop and explain the electrical schematic for the excitation coil in series and in…

Q: What is the correct way to measure current in a completed circuit using a DMM? O Connected in series…

A: MultimeterThis type of meter is used for the measurement of electrical characteristics. It can…

Q: What is Pre charge circuit and what is the use of it inside the junction boxes?

A: A pre-charge circuit is an electronic circuit used to gradually apply voltage to a circuit or system…

Q: Adopt a customer perspective and state what features of circuit breakers are critical to quality…

A:

Q: Create a Sequence Diagram about Temperature Controlled Electric Fan with the following: *Thermistor…

A: Sequence Diagram of temperature controlled electric fan shows that how the fan works with the sensor…

Q: Explain the following picture and its' importance in selection of circuit breakers. Extinction of…

A: to explain the following picture and its importance in selection of circuit breakers

Q: 9) Does this switch (in the open state) have a Low resistance or a high resistance between its…

A: In this question,  We need to determine and check the resistance low or high as per given the open…

Q: How to turn-off a current source? A) Set it to zero. B) Replace it with a short-circuit. (C) You…

A: What is the process to turn of the current source  : Options are : Set it to Zero. Replace it with…

Q: of the following statements is true for an SCR. It is an on-only controllable switch, which is…

A: There are three types of switches: Uncontrolled switches : In these turn on and turn off can not be…

Q: Is there any iron lost in the short circuit test? If there is, why is it omitted

A: Yes, in short circuit test, iron losses or core losses are not absent (or zero) but they are…

Q: L 1. A single SPST switch is rated for 20 A/28V. Can this switch be used to control a 12-V, 540-W…

A: Given Data:An SPST switch with,Current rating Voltage rating Load voltage Load power To…

Q: What is the minimum wire size for a 30 amp circuit?

A: To determine the minimum wire size for a 30 amp circuit. For the minimum wire size refer the NEC…

Q: 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz…

A: A full-wave rectifier is AC to DC converter. A three-phase fully controlled rectifier converts AC…

Q: What are the functions of a Transfer Switch: (Select all answers that apply) Group of answer…

A: functions of a Transfer Switch:

Q: What are the two types of clipper circuit used in non linear devices?

A: Positive & Negative Clipper Positive Clipper can be used to slice off a portion of the positive…

Q: What are the key requirements for fuses for overcurrent protection? A thyristor gate can be…

A: Fuse and thyristor

Q: What is the function of deadtime? A. Ensure the high-side switch has an adequate Vgs B. Increase…

A: Dead time : It is a period in which both upper and lower switches leg are off.  Dead time can be…

Q: Q2-: For two input-one output home power source changeover switch do : - Draw the complete wiring.…

A: To draw wiring diagrams of PLC

Q: In the next figure.we want to fill the two tanks with water by a pump. The pump is operating…

A: Step 1:A diagram given states:The pump is operated manually by a push-button "Start" (normally open)…

Q: Describe and Explain what occurs in each of these circuits when the pushbutton switch is actuated…

A: The SCR is a unidirectional device that allows the current to flow in one direction and opposes it…

Methods of Wiring

Electrical wiring is the way of integrating cables and wires to interconnected equipment such as fuses, switches, sockets, lights, fans, and so on to the main distribution board, which is a specific structure attached to the utility pole that ensures a constant power supply.